View XR17V258_628113.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

xr
NOVEMBER 2005
XR17V258
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.0
GENERAL DESCRIPTION
The XR17V2581 (V258) is a single chip 8-channel 66MHz PCI (Peripheral Component Interconnect) UART (Universal Asynchronous Receiver and Transmitter) solution, optimized for higher performance and lower power. The V258 device with its fifth generation register set is designed to meet the high bandwidth and power management requirements for multi-serial communication ports for system administration and management. The 32-bit 66MHz PCI interface is compliant with PCI 3.0 and PCI power management revision 1.1 specifications. The device provides an upgrade path for Exar's 33MHz 5V and Universal PCI UART family of products in a 144-pin LQFP package. The V258 consists of eight independent UART channels, each with set of configuration and enhanced registers, 64 bytes of Transmit (TX) and Receive (RX) FIFOs, and a fractional Baud Rate Generator (BRG). A global interrupt source register provides a complete interrupt status indication for all 8-channels to speed up interrupt parsing. The V258 device operates at 33/66MHz and features fully programmable TX and RX FIFO level triggers, automatic hardware and software flow control, and automatic RS-485 half duplex direction control output for software and hardware design simplification.
NOTE 1: Covered by U.S. Patents #5,649,122 and #5,949,787
* Factory Automation and Process Control * Instrumentation * Multi-port RS-232/RS-422/RS-485 Cards * Point-of-Sale Systems
FEATURES
* High performance 32-bit 66MHz PCI UART * PCI 3.0 compliance * PCI power management rev. 1.1 compliance * EEPROM interface for PCI configuration * 3.3V supply with 5V tolerant non-PCI (serial) inputs * Data read/write burst operation * Global interrupt register for all eight UART channels * Up to 8 Mbps serial data rate * Eight multi-purpose inputs/outputs * A 16-bit general purpose timer/counter * Sleep mode with wake-up Indicator * Eight independent UART channels controlled with

APPLICATIONS
* Remote Access Servers * Storage Network Management
FIGURE 1. BLOCK DIAGRAM OF THE XR17V258
16C550 compatible register Set 64-byte TX and RX FIFOs with level counters and programmable trigger levels Fractional baud rate generator Automatic RTS/CTS or DTR/DSR hardware flow control with programmable hysteresis Automatic Xon/Xoff software flow control RS-485 half duplex direction control output with selectable turn-around delay Infrared (IrDA 1.0) data encoder/decoder Programmable data rate with prescaler
AD [31 :0] C /B E#[3:0]
U AR T C h an nel 0
64-b yte TX FIFO UA RT IR Re gs TX & RX EN D E C BR G 64-b yte RX FIFO
T X[7:0] R X[7:0]
P AR F R AM E # T R D Y# IR D Y# S T OP # D E VS E L # ID S E L # 33/66M H z CL K R ST# P E RR # S E RR # IN T A# PME# E N IR E E CK EEDI EEDO E E CS
C onfiguration Space R e giste rs 16-bit T ime r/C ounte r
R TS#[7:0]
PC I L o ca l Bu s Int erfa ce
Global C o n fig u ratio n R eg isters
U AR T C h an nel 1 U AR T C h an nel 2 U AR T C h an nel 3 U AR T C h an nel 4 U AR T C h an nel 5 U AR T C h an nel 6
R I#[7:0] D SR #[7:0] D TR #[7:0] C TS #[7:0]
D CD #[7:0]
U AR T C h an nel 7 M u lti-p u rp o se In p u ts/Ou tp u ts C rystal Osc/B u ffer
M PIO [7:0]
E E PR OM In terface
X T AL 1/C L K X T AL 2 T MR C K
Exar Corporation 48720 Kato Road, Fremont CA, 94538 * (510) 668-7000 * FAX (510) 668-7017 * www.exar.com
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT FIGURE 2. PIN OUT OF THE DEVICE
DSR4# DTR3# 101 DSR2# DSR3# 100 CTS2# 79 DTR5# DSR5# DTR2# DTR4# MPIO0 MPIO1 CTS4# RTS2# RTS3# CTS3# RTS5# 86 RTS4#
xr
REV. 1.0.0
103 RI2#
107
104
91 RX3
99
98
97
96
95
94
93
92
90
89
88
87
85
84
83
82
81
108
106
105
102
80
78
77
76
75
74
MPIO2
CD2#
CD3#
CD4#
RI3#
RI4#
RX2
RX4
RI5#
TX2
TX3
TX4
CD5#
XTAL2 109 XTAL1 110 PME# VCC 111 112
73
MPIO3
GND
VCC
TX5
72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56
CTS5# RX5 ENIR TMRCK MPIO4 MPIO5 MPIO6 MPIO7 VCC GND TX6 DTR6# RTS6# RI6# CD6# DSR6# CTS6# RX6 TX7 DTR7# RTS7# RI7# CD7# DSR7# CTS7# RX7 GND VCC AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7
EEDO 113 EEDI EECS EECK TX1 114 115 116 117
DTR1# 118 RTS1# 119 RI1# CD1# 120 121
DSR1# 122 CTS1# 123 RX1 TX0 124 125
DTR0# 126 RTS0# 127 RI0# CD0# 128 129
XR17V258
55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 31 27 32 35 GND 33
DSR0# 130 CTS0# 131 RX0 INTA# RST# CLK GND VCC AD31 AD30 AD29 AD28 AD27 AD26 AD25 132 133 134 135 136 137 138 139 140 141 142 143 144 11 12 17 DEVSEL# 18 19 20 STOP# 21 24 CBE1 25 28 29 PERR# 22 SERR# 23 10 13 CBE2 14 FRAME# 15 IRDY# 16 26 30 34 36 CBE0 1 2 4 3 5 6 7 8 9
IDSEL
CBE3
TRDY#
AD24
AD23
AD17
GND
AD22
AD20
AD19
AD16
AD21
AD18
AD15
AD14
AD13
AD12
AD11
AD10
VCC
GND
VCC
PAR
AD9
ORDERING INFORMATION
PART NUMBER XR17V258IV PACKAGE 144-Lead LQFP OPERATING TEMPERATURE RANGE -40C to +85C DEVICE STATUS Active
2
AD8
VCC
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
PIN DESCRIPTIONS
NAME PIN # TYPE DESCRIPTION PCI LOCAL BUS INTERFACE RST# 134 I PCI bus reset input (active LOW). It resets the PCI local bus configuration space registers, device configuration registers and UART channel registers to the default condition. PCI bus clock input of up to 66.67MHz. Address data lines [31:0] (bidirectional).
CLK AD31-AD25, AD24, AD23-AD16, AD15-AD8, AD7-AD0 FRAME# C/BE0#C/BE3# IRDY#
135 138-144, 1, 6-13, 26-33, 37-44 15 36,25,14,2 16
I IO
I I I
Bus transaction cycle frame (active LOW). It indicates the beginning and duration of an access. Bus command/byte enable [3:0] (active LOW). This line is multiplexed for bus command during the address phase and byte enables during the data phase. Initiator ready (active LOW). During a write, it indicates that valid data is present on data bus. During a read, it indicates the master is ready to accept data. Target ready (active LOW). Target request to stop current transaction (active LOW). Initialization device select (active HIGH). Device select to the XR17V258 (active LOW). Device interrupt from XR17V258 (open drain, active LOW). Power Management Event signal. While in D3hot state, if the PME_Enable bit in the Power Management Control/Status Register is set, the V258 asserts the PME# upon receiving a new character or upon change of state of modem inputs on any channel. Parity is even across AD[31:0] and C/BE[3:0]# (bidirectional, active HIGH). Data parity error indicator, except for special cycle transactions (active LOW). Optional in bus target application. System error indicator, Address parity or data parity during special cycle transactions (open drain, active LOW). Optional in bus target application.
TRDY# STOP# IDSEL DEVSEL# INTA# PME#
17 21 3 18 133 111
O O I O OD OD
PAR PERR# SERR#
24 22 23
IO O OD
MODEM OR SERIAL I/O INTERFACE TX0 RX0 125 132 O I UART channel 0 Transmit Data or infrared transmit data. UART channel 0 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted internally prior to decoding by setting FCTR bit [4]. UART channel 0 Request to Send or general purpose output (active LOW). UART channel 0 Clear to Send or general purpose input (active LOW).
RTS0# CTS0#
127 131
O I
3
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
PIN DESCRIPTIONS
NAME DTR0# DSR0# CD0# RI0# TX1 RX1 PIN # 126 130 129 128 117 124 TYPE O I I I O I DESCRIPTION UART channel 0 Data Terminal Ready or general purpose output (active LOW). UART channel 0 Data Set Ready or general purpose input (active LOW). UART channel 0 Carrier Detect or general purpose input (active LOW). UART channel 0 Ring Indicator or general purpose input (active LOW). UART channel 1 Transmit Data or infrared transmit data. UART channel 1 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted prior to decoding by setting FCTR bit [4]. UART channel 1 Request to Send or general purpose output (active LOW). UART channel 1 Clear to Send or general purpose input (active LOW). UART channel 1 Data Terminal Ready or general purpose output (active LOW). UART channel 1 Data Set Ready or general purpose input (active LOW). UART channel 1 Carrier Detect or general purpose input (active LOW). UART channel 1 Ring Indicator or general purpose input (active LOW). UART channel 2 Transmit Data or infrared transmit data. UART channel 2 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted prior to decoding by setting FCTR bit [4]. UART channel 2 Request to Send or general purpose output (active LOW). UART channel 2 Clear to Send or general purpose input (active LOW). UART channel 2 Data Terminal Ready or general purpose output (active LOW). UART channel 2 Data Set Ready or general purpose input (active LOW). UART channel 2 Carrier Detect or general purpose input (active LOW). UART channel 2 Ring Indicator or general purpose input (active LOW). UART channel 3 Transmit Data or infrared transmit data. UART channel 3 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted prior to decoding by setting FCTR bit [4]. UART channel 3 Request to Send or general purpose output (active LOW). UART channel 3 Clear to Send or general purpose input (active LOW). UART channel 3 Data Terminal Ready or general purpose output (active LOW). UART channel 3 Data Set Ready or general purpose input (active LOW). UART channel 3 Carrier Detect or general purpose input (active LOW).
RTS1# CTS1# DTR1# DSR1# CD1# RI1# TX2 RX2
119 123 118 122 121 120 106 99
O I O I I I O I
RTS2# CTS2# DTR2# DSR2# CD2# RI2# TX3 RX3
104 100 105 101 102 103 98 91
O I O I I I O I
RTS3# CTS3# DTR3# DSR3# CD3#
96 92 97 93 94
O I O I I
4
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
PIN DESCRIPTIONS
NAME RI3# TX4 RX4 PIN # 95 88 81 TYPE I O I DESCRIPTION UART channel 3 Ring Indicator or general purpose input (active LOW). UART channel 4 Transmit Data or infrared transmit data. UART channel 4 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted prior to decoding by setting FCTR bit [4]. UART channel 4 Request to Send or general purpose output (active LOW). UART channel 4 Clear to Send or general purpose input (active LOW). UART channel 4 Data Terminal Ready or general purpose output (active LOW). UART channel 4 Data Set Ready or general purpose input (active LOW). UART channel 4 Carrier Detect or general purpose input (active LOW). UART channel 4 Ring Indicator or general purpose input (active LOW). UART channel 5 Transmit Data or infrared transmit data. UART channel 5 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted prior to decoding by setting FCTR bit [4]. UART channel 5 Request to Send or general purpose output (active LOW). UART channel 5 Clear to Send or general purpose input (active LOW). UART channel 5 Data Terminal Ready or general purpose output (active LOW). UART channel 5 Data Set Ready or general purpose input (active LOW). UART channel 5 Carrier Detect or general purpose input (active LOW). UART channel 5 Ring Indicator or general purpose input (active LOW). UART channel 6 Transmit Data or infrared transmit data. UART channel 6 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted prior to decoding by setting FCTR bit [4]. UART channel 6 Request to Send or general purpose output (active LOW). UART channel 6 Clear to Send or general purpose input (active LOW). UART channel 6 Data Terminal Ready or general purpose output (active LOW). UART channel 6 Data Set Ready or general purpose input (active LOW). UART channel 6 Carrier Detect or general purpose input (active LOW). UART channel 6 Ring Indicator or general purpose input (active LOW). UART channel 7 Transmit Data or infrared transmit data.
RTS4# CTS4# DTR4# DSR4# CD4# RI4# TX5 RX5
86 82 87 83 84 85 80 71
O I O I I I O I
RTS5# CTS5# DTR5# DSR5# CD5# RI5# TX6 RX6
78 72 79 75 76 77 62 55
O I O I I I O I
RTS6# CTS6# DTR6# DSR6# CD6# RI6# TX7
60 56 61 57 58 59 54
O I O I I I O
5
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
PIN DESCRIPTIONS
NAME RX7 PIN # 47 TYPE I DESCRIPTION UART channel 7 Receive Data or infrared receive data. Normal RXD input idles at HIGH condition. The infrared pulses can be inverted prior to decoding by setting FCTR bit [4]. UART channel 7 Request to Send or general purpose output (active LOW). UART channel 7 Clear to Send or general purpose input (active LOW). UART channel 7 Data Terminal Ready or general purpose output (active LOW). UART channel 7 Data Set Ready or general purpose input (active LOW). UART channel 7 Carrier Detect or general purpose input (active LOW). UART channel 7 Ring Indicator or general purpose input (active LOW).
RTS7# CTS7# DTR7# DSR7# CD7# RI7# ANCILLARY SIGNALS MPIO0 MPIO1 MPIO2 MPIO3 MPIO4 MPIO5 MPIO6 MPIO7 EECK
52 48 53 49 50 51
O I O I I I
108 107 74 73 68 67 66 65 116
I/O I/O I/O I/O I/O I/O I/O I/O O
Multi-purpose input/output 0. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT Multi-purpose input/output 1. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT. Multi-purpose input/output 2. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT. Multi-purpose input/output 3. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT. Multi-purpose input/output 4. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT. Multi-purpose input/output 5. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT. Multi-purpose input/output 6. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT. Multi-purpose input/output 7. The function of this pin is defined thru the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT. Serial clock to EEPROM. An internal clock of CLK divide by 256 is used for reading the vendor and sub-vendor ID during power up or reset. However, it can be manually clocked thru the Configuration Register REGB. Chip select to a EEPROM device like 93C46. It is manually selectable thru the Configuration Register REGB. Requires a pull-up 4.7K ohm resistor for external sensing of EEPROM during power up. See DAN112 for further details. Write data to EEPROM device. It is manually accessible thru the Configuration Register REGB. Read data from EEPROM device. It is manually accessible thru the Configuration Register REGB. Crystal or external clock input. Crystal or buffered clock output.
EECS
115
O
EEDI EEDO XTAL1 XTAL2
114 113 110 109
O I I O
6
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
PIN DESCRIPTIONS
NAME TMRCK ENIR PIN # 69 70 TYPE I I DESCRIPTION 16-bit timer/counter external clock input. Infrared mode enable (active high). This pin is sampled during power up, following a hardware reset (RST#) or soft-reset (register RESET). It can be used to start up all 8 UARTs in the infrared mode. The sampled logic state is transferred to MCR bit [6] in the UART. Power supply for the UART core logic and PCI bus I/O - 3.3V only. The V258 is PCI 3.0 signalling compliant at 3.3V operation. The non-PCI inputs (except XTAL1) are 5V tolerant. This includes all the serial (modem) inputs. Power supply common, ground.
VCC
64, 90,112, 4, 19, 34, 45, 137 5,20,35,46,63, 89,136
GND
NOTE: Pin type: I=Input, O=Output, IO= Input/output, OD=Output Open Drain.
7
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
FUNCTIONAL DESCRIPTION
The XR17V258 (V258) consists of eight enhanced 16550 UARTs with a conventional PCI interface and a nonvolatile memory interface for PCI plug-and-play auto-configuration. The PCI local bus is a synchronous timing bus where all bus transactions are associated with the bus clock. The V258 supports 66MHz clock and 32-bit wide read and write data transfer operations including data burst mode through the PCI interface. Read and write data operations may be in byte, word or double-word (DWORD) format. The device consists of three sets of registers:
* PCI local bus configuration registers for PCI auto configuration * 32-bit global device configuration registers for overall control and monitoring of the 8 UART channels. * A combination set of the 16C550 compatible registers and enhanced registers in each of the individual UART
channel, for control, status, and byte wide data transfer Each UART channel has 64-byte FIFOs, automatic RTS/CTS or DTR/DSR hardware flow control with hysteresis control, automatic Xon/Xoff software flow control, programmable transmit and receive FIFO trigger level, FIFO level counters, infrared encoder and decoder (IrDA ver. 1.0), and a programmable fractional baud rate generator with a prescaler of 1X or 4X, and data rate up to 8 Mbps at 8X sampling clock.The XR17V258 is available in a 144-pin LQFP (20x20x1.4mm) industrial grade package. PCI LOCAL BUS INTERFACE This is the host interface and it meets the PCI local bus specification revision 3.0. The PCI local bus operations are synchronous, where each transaction is associated to the bus clock. The V258 can operate with the bus clock of up to a 66.67MHz. Data transfers operation can be formatted in 8-bit, 16-bit, 24-bit or 32-bit wide. With 32-bit data operations, it pushes the data transfer rate on the bus up to 264 MByte/sec. This increases the overall system's communication performance up to 32 times better than the 8-bit ISA bus. See PCI local bus specification revision 3.0 for bus operation details. PCI LOCAL BUS CONFIGURATION SPACE REGISTERS A set of PCI local bus configuration space register is provided. These registers provide the PCI local bus operating system with the card's vendor ID, device ID, sub-vendor ID, product model number, and resources and capabilities. The PCI local bus operating system collects this data from all the cards on the bus during the auto configuration phase that follows immediately after a power up or system reset/reboot. After it has sorted out all devices on the bus, it defines and download the operating conditions to the cards. One of the definitions is the base address loaded into the Base Address Register (BAR) where the card will be operating in the PCI local bus memory space. All this is described in more detail in "Section 1.1, PCI LOCAL BUS CONFIGURATION SPACE REGISTERS" on page 9. POWER MANAGEMENT REGISTERS This set of registers is a continuation of the Configuration Space and provides status and control of Power Management functions of the V258. The Power Management Capabilities (PMC) register and the Power Management Control/Status Register (PMCSR) are implemented. "Section 1.2, Power Management Registers" on page 11 describes these registers and details how Power Management is implemented in the device. EEPROM INTERFACE An external 93C46 EEPROM is used to store 8 words of information. Details of this information can be found in "Section 1.4, EEPROM Interface" on page 14. This information is only used with the plug-and-play auto configuration of the PCI local bus. These data provide automatic hardware installation onto the PCI bus. The EEPROM interface consists of 4 signals, EEDI, EEDO, EECS, and EECK. The EEPROM is not needed when auto configuration is not required in the application. However, if your design requires non-volatile memory for other purpose, it is possible to store and retrieve data on the EEPROM through a special PCI device configuration register. See application note DAN112 for its programming details.
8
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
1.0 XR17V258 INTERNAL REGISTERS The XR17V258 UART has three different sets of registers as shown in Figure 3. The PCI Local Bus Configuration Space Registers are for plug-and-play auto-configuration when connecting the device to the PCI bus. This auto-configuration feature makes installation very easy into a PCI system and it is part of the PCI local bus specification. The second register set is the Device Configuration Registers that are also accessible directly from the PCI bus for programming general operating conditions of the device and monitoring the status of various functions common to all eight channels. These functions include all 8 channel UARTs' interrupt control and status, 16-bit general purpose timer control and status, multipurpose inputs/ outputs control and status, sleep mode, soft-reset, and device identification and revision. And lastly, each UART channel has its own set of internal UART Configuration Registers for its own operation control and status reporting. All 8 sets of channel registers are embedded inside the device configuration registers space, which provides faster access. The second and third set of registers are mapped into 4K of the PCI bus memory address space. The following paragraphs describe all 3 sets of registers in detail. FIGURE 3. THE XR17V258 REGISTER SETS
PC I Loc al Bus C onfig ur ation Spac e R eg is ter s for Plug and- Play Auto C onfig ur ation
D evic e C onfig ur ation and U AR T [7:0] C onfig ur ation R eg is ter s ar e mapped on to the Bas e Addr es s R eg is ter ( BAR ) in a 4Kbyte of memor y addr es s s pac e
Vendor and Sub- vendor ID and Pr oduc t M odel N umber in Exter nal EEPR O M
C hannel 0 IN T , M PIO , T IM ER ,R EG C hannel 0
0 x0 0 0 0 0 x0 0 8 0 D evic e 8 C onfig ur ation R eg is ter s c hannel Inter r upts , M ultipur pos e I/O s , 16- bit T imer /C ounter , Sleep, R es et, D VID , D R EV
PC I Loc al Bus Inter fac e
C hannel 1 C hannel 2 C hannel 3 C hannel 4 C hannel 5 C hannel 6 C hannel 7
0 x0 2 0 0 0 x0 4 0 0 0 x0 6 0 0 0 x0 8 0 0 0 x0 A 0 0 0x0C 00 0x0E00 0x0F F F
U AR T [7:0] C onfig ur ation R eg is ter s 16550 C ompatible and EXAR Enhanc ed R eg is ter s
P CI RE G S -1
1.1
PCI LOCAL BUS CONFIGURATION SPACE REGISTERS
The PCI local bus configuration space registers are responsible for setting up the device's operating environment in the PCI local bus. The pre-defined operating parameters of the device is read by the PCI bus plug-and-play auto-configuration manager in the operating system. After the PCI bus has collected all data from every device/card on the bus, it defines and downloads the memory mapping information to each device/ card about their individual operation memory address location and conditions. The operating memory mapped address location is downloaded into the Base Address Register (BAR) register, located at an address offset of 0x10 in the configuration space. Custom modification of certain registers is possible by using an external 93C46 EEPROM. The EEPROM contains the device vendor and sub-vendor data, along with 6 other words of information (see "Section 1.4, EEPROM Interface" on page 14) required by the auto-configuration setup.
9
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 1: PCI LOCAL BUS CONFIGURATION SPACE REGISTERS
ADDRESS OFFSET 0x00 BITS 31:16 15:0 0x04 31 30 29:28 27 26:25 24 23 22 21 20 19:16 15:9,7, 5,4,3,2 8 6 1 0 0x08 31:8 7:0 0x0C 31:24 23:16 15:8 7:0 0x10 31:12 11:0 0x14 0x18h 0x1C 0x20 31:0 31:0 31:0 31:0 TYPE EWR EWR RWC RWC RO RO RO RO RO RO RO RO RO RO RWR RWR RWR RO EWR RO RO RO RO RO RWR RO RO RO RO RO DESCRIPTION Device ID (Exar device ID number) Vendor ID (Exar) specified by PCISIG Parity error detected. Cleared by writing a logic 1. System error detected. Cleared by writing a logic 1. Unused Target Abort. DEVSEL# timing. Unemployments bus master error reporting bit Fast back to back transactions are supported Reserved Status bit 66MHz capable Capabilities List Reserved Status bits Command bits (reserved) SERR# driver enable. logic 1=enable driver and 0=disable driver Parity error enable. logic 1=respond to parity error and 0=ignore Command controls a device's response to mem space accesses: 0=disable mem space accesses, 1=enable mem space accesses Device's response to I/O space accesses is disabled. (0 = disable I/O space accesses) Class Code (Default is 'Simple 550 Communication Controller') Revision ID (Exar device revision number) BIST (Built-in Self Test) Header Type (a single function device with one BAR) Unimplemented Latency Timer (needed only for bus master) Unimplemented Cache Line Size Memory Base Address Register (BAR) Claims a 4K address space for the memory mapped UARTs Unimplemented Base Address Register (returns zeros) Unimplemented Base Address Register (returns zeros) Unimplemented Base Address Register (returns zeros) Unimplemented Base Address Register (returns zeros)
xr
REV. 1.0.0
RESET VALUE (HEX OR BINARY) 0x0258 0x13A8 0b 0b 00b 0b 00b 0b 1b 0b 1b 1b 0000b 0x0000 0b 0b 0b 0b 0x070002 Current Rev. value 0x00 0x00 0x00 0x00 0x00 0x000 0x00000000 0x00000000 0x00000000 0x00000000
10
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 1: PCI LOCAL BUS CONFIGURATION SPACE REGISTERS
ADDRESS OFFSET 0x24 0x28 0x2C
BITS 31:0 31:0 31:16 15:0
TYPE RO RO EWR EWR RO RO RO RO RO RO RO RWR
DESCRIPTION Unimplemented Base Address Register (returns zeros) Reserved Subsystem ID (write from external EEPROM by customer) Subsystem Vendor ID (write from external EEPROM by customer) Expansion ROM Base Address (Unimplemented) Reserved (returns zeros) Capability Pointer (Implemented for Power Management) Reserved (returns zeros) Unimplemented MAXLAT Unimplemented MINGNT Interrupt Pin, use INTA#. Interrupt Line.
RESET VALUE (HEX OR BINARY) 0x00000000 0x00000000 0x0000 0x0000 0x00000000 0x000000 0x40 0x00000000 0x00 0x00 0x01 0xXX
0x30 0x34
31:0 31:8 7:0
0x38 0x3C
31:0 31:24 23:16 15:8 7:0
NOTE: EWR=Read/Write from external EEPROM. RWR=Read/Write from AD[31:0]. RO= Read Only. RWC=Read/WriteClear.
1.2
Power Management Registers
The Power Management Registers are implemented in 2 DWORDs starting at address offset 0x40 of the PCI local bus configuration space. The bit definitions of these registers are shown in Table 2 below. The V258 complies with Revision 1.1 of the PCI Power Management Interface Specification. TABLE 2: POWER MANAGEMENT REGISTERS
ADDRESS OFFSET 0x40 BITS 31:16 31:27 26:20 19 18:16 15:8 7:0 0x44 31:24 23:16 15:0 15 14:9 TYPE See Below RO RO RO RO RO RO RO RO See Below RWC RO DESCRIPTION Power Management Capabilities (PMC) PME Support (PME# can be asserted from D3hot only) Reserved or Not Supported PME Clock (PCI clock is required for PME# generation) Version Next Item Pointer Capability ID Unimplemented Data Register Unimplemented Bridge Support Extensions Power Management Control/Status Register (PMCSR) PME_Status Reserved RESET VALUE (HEX OR BINARY) See Below 01000b 0000000b 1b 010b 0x00 0x01 0x00 0x00 See Below 0b 00000b
11
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 2: POWER MANAGEMENT REGISTERS
ADDRESS OFFSET BITS 8 7:2 1:0 TYPE RWR RO RWR DESCRIPTION PME_Enable Reserved PowerState
xr
REV. 1.0.0
RESET VALUE (HEX OR BINARY) 0b 000000b 00b
NOTE: RWR=Read/Write from AD[31:0]. RO= Read Only. RWC=Read/Write-Clear.
1.2.1
Power States and Power State Transitions of the V258
The XR17V258 supports D0, D3hot and D3cold power states and is capable of generating the PME# signal from the D3hot state. The following paragraphs describe these power states and Figure 4 shows the power state transitions of the V258. D0 STATE The XR17V258 must be placed in the D0 state before being used in a system. The D0 state represents two states - D0 Uninitalized and D0 Active. Upon entering D0 from power up or transition from D3hot, the V258 will be in the D0 Uninitialized state. Once initialized by the system software, the V258 will enter the D0 Active state. In the D0 Active state, the V258 is fully functional and will respond to all PCI bus transactions as well as issue interrupts (INTA#). The system software can program the V258 to enter the D3hot state from the D0 state. D3HOT STATE The V258 enters the D3hot state when the system software programs the V258 from D0 to D3hot, via PMCSR bits [1:0]. In this state, the V258 will not be fully functional. The V258 will respond only to PCI configuration space accesses, if a PCI clock is provided and will not respond to PCI memory accesses nor will it issue interrupts. However, the V258 will continue to receive data and the automatic software and hardware flow control, if enabled, will continue to function normally. While in the D3hot state, the V258 asserts the PME# (Power Management Event) signal, if enabled by setting PME_Enable bit (bit-8 of PMCSR), upon one of the following events:

RX pin of any of the channels goes LOW (START bit detected), or Any of the delta bits of modem inputs (MSR register bits [3:0]) is set in any of the 8 channels (see page 50)
The V258 also sets the PME_Status bit when such an event occurs, regardless of whether the PME_Enable bit is set or not. The system software can reset the PME_Status bit by writing a '1' to it. When the system software programs the V258 from D3hot to D0, typically in response to the PME# signal, the V258 enters the D0 Active state and will retain all the values of its internal registers. The V258 will keep its PCI signal drivers disabled for the duration of the D3hot to D0 Uninitialized state transition. The V258 saves the PME context (configuration registers and functional state information) in the D3hot state. Note: The V258 has a sleep mode which keeps the power consumption to a minimum (see Sleep Mode description on page 24). This is independent of the power state the V258 is in. The user can optionally place the V258 in sleep mode (via the software driver) in the Active D0 state anytime or specifically when the system software commands the V258 to enter the D3hot state. The crystal oscillator shuts down when the conditions given in Sleep Mode section on page 24 are satisfied, and re-starts when one of the events as described in the same section occurs. Upon re-starting, the oscillator may take a long time to settle. This time may be more than 20ms which is the maximum wait time guaranteed by the system software before resuming normal PCI bus transactions in the Active D0 state. Therefore, there may be data errors if the V258 is commanded to transmit data before the oscillator is ready. It is recommended not to use sleep mode while in the D3hot state for this reason.
12
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
D3COLD STATE The V258 enters the state when power is removed from the device. All context is lost in this state and the V258 does not support PME# in this state. When power is restored, PCI RST# must be asserted and the V258 will return to the D0 Uninitialized state with a full PCI 3.0 compliant power-on reset sequence. The V258 will set all its registers and outputs to the power-on defaults just as at initial power up. The system software must then fully initialize and re-configure the V258 to place it in the D0 Active state. FIGURE 4. POWER STATE TRANSITIONS OF THE XR17V258
Power on + PCI RST#
D0 Uninitialized
Power on + PCI RST#
D0 Active
D3cold
VCC Removed
D3hot
1.3
Special Read/Write Register to store User Information
This 32-bit register can be used to store user information and is writable only via the EEPROM. This is implemented at an offset of 0x48 in the PCI Configuration Space immediately following the Power Management Registers. This register can be used to store application-specific information which may be used by the device driver to initialize the device appropriately. TABLE 3: SPECIAL READ/WRITE REGISTER
ADDRESS OFFSET 0x48 BITS 31:0 TYPE EWR DESCRIPTION User Information Writable only through EEPROM RESET VALUE (HEX) 0x00000000
NOTE: EWR=Read/Write from external EEPROM.
13
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 1.4 EEPROM Interface
xr
REV. 1.0.0
The V258 provides an interface to an Electrically Erasable Programmable Read Only Memory (EEPROM). The EEPROM must be a 93C46-like device, with its memory configured as 16-bit words. This interface is provided in order to program the registers in the PCI Configuration Space of the PCI UART during power-up. The following table gives the mapping of the EEPROM memory to the registers in the V258's PCI Configuration Space. When the PCI RST# is negated, the V258 will download the data from the EEPROM, if it detects a HIGH on the EECS pin. The V258 takes a maximum of 216 PCI clocks from the rising edge of the PCI RST# signal to read the EEPROM data. For more details on the EEPROM interface, please refer to the application note DAN112 on Exar's website.
TABLE 4: EEPROM ADDRESS DEFINITIONS
EEPROM MEMORY ADDRESS 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 EEPROM DATA [D15:D0] Vendor ID Device ID Class Code* Class Code (Continued) Subsystem Vendor ID Subsystem ID Special Register (Lower Word) Special Register (Upper Word) V258'S PCI CONFIGURATION SPACE ADDRESS (WORD OFFSET) 0x00 0x02 0x08 0x0A 0x2C 0x2E 0x48 0x4A DEFAULT VALUES 0x13A8 0x0258 0x0200 0x0700 0x0000 0x0000 0x0000 0x0000
NOTE: * Only the upper 8 bits in this word in EEPROM location are used and the lower 8 bits are ignored. The lower byte at PCI Config space 0x08 is Device Revision and is read-only.
1.5
Device Internal Register Sets
The Device Configuration Registers and the eight individual UART Configuration Registers of the V258 occupy 4K of PCI bus memory address space. These addresses are offset onto the basic memory address, a value loaded into the Memory Base Address Register (BAR) in the PCI local bus configuration register set. The UART Configuration Registers are mapped into 8 address blocks where each UART channel occupies 512 bytes memory space for its own registers that include the 16550 compatible registers. The Device Configuration Registers are embedded inside the UART channel zero's address space between 0x0080 to 0x0093. All these registers can be accessed in 8, 16, 24 or 32 bits width depending on the starting address given by the host at the beginning of the bus cycle. Transmit and receive data may be loaded or unloaded in 8, 16, 24 or 32 bits format in special locations given in the Table 5 below. Every time a read or write operation is made to the transmit or receive register, its FIFO data pointer is automatically bumped to the next sequential data location either in byte, word or DWORD. One special case applies to the receive data unloading when reading the receive data together with its LSR register content. The host must read them in 16 or 32 bits format in order to maintain integrity of the data byte with its associated error flags. These special registers are further discussed in "Section 3.1, FIFO DATA LOADING AND UNLOADING IN 32-BIT FORMAT." on page 28.
14
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 5: XR17V258 UART AND DEVICE CONFIGURATION REGISTERS
OFFSET ADDRESS 0x000 - 0x00F 0x010 - 0x07F 0x080 - 0x093 0x094 - 0x0FF 0x100 0x100 0x140 - 0x17F 0x180 - 0x1FF
MEMORY SPACE UART channel 0 Regs Reserved DEVICE CONFIGURATION REGISTERS Reserved UART 0 - Read FIFO UART 0 - Write FIFO Reserved UART 0 - Read FIFO with errors
READ/WRITE (Table 13 &
DATA WIDTH 8/16/24/32
COMMENT First 8 regs are 16550 compatible
Table 14)
(Table 6) 8/16/24/32
Read-Only Write-Only
8/16/24/32 8/16/24/32
64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
0x200 - 0x20F 0x210 - 0x2FF 0x300 0x300 0x340 - 0x37F 0x380 - 0x3FF
UART channel 1 Regs Reserved UART 1 - Read FIFO UART 1 - Write FIFO Reserved UART 1 - Read FIFO with errors
(Table 13 &
8/16//24/32
First 8 regs are 16550 compatible
Table 14)
Read-Only Write-Only 8/16/24/32 8/16/24/32 64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
0x400 - 0x40F 0x410 - 0x4FF 0x500 0x500 0x540 - 0x57F 0x580 - 0x5FF
UART channel 2 Regs Reserved UART 2 - Read FIFO UART 2 - Write FIFO Reserved UART 2 - Read FIFO with errors
(Table 13 &
8/16/24/32
First 8 regs are 16550 compatible
Table 14)
Read-Only Write-Only 8/16/24/32 8/16/24/32 64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
0x600 - 0x60F 0x610 - 0x6FF 0x700 0x700 0x740 - 0x77F 0x780 - 0x7FF
UART channel 3 Regs Reserved UART 3 - Read FIFO UART 3 - Write FIFO Reserved UART 3 - Read FIFO with errors
(Table 13 &
8/16/24/32
First 8 regs are 16550 compatible
Table 14)
Read-Only Write-Only 8/16/24/32 8/16/24/32 64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
15
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 5: XR17V258 UART AND DEVICE CONFIGURATION REGISTERS
OFFSET ADDRESS MEMORY SPACE READ/WRITE DATA WIDTH
xr
REV. 1.0.0
COMMENT
0x800 - 0x80F 0x810 - 0x8FF 0x900 0x900 0x940 - 0x97F 0x980 - 0x9FF
UART channel 4 Regs Reserved UART 4 - Read FIFO UART 4 - Write FIFO Reserved UART 4 - Read FIFO with errors
(Table 13 &
8/16/24/32
First 8 regs are 16550 compatible
Table 14)
Read-Only Write-Only 8/16/24/32 8/16/24/32 64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
0xA00 - 0xA0F 0xA10 - 0xAFF 0xB00 0xB00 0xB40 - 0xB7F 0xB80 - 0xBFF
UART channel 5 Regs Reserved UART 5 - Read FIFO UART 5 - Write FIFO Reserved UART 5 - Read FIFO with errors
(Table 13 &
8/16/24/32
First 8 regs are 16550 compatible
Table 14)
Read-Only Write-Only 8/16/24/32 8/16/24/32 64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
0xC00 - 0xC0F 0xC10 - 0xCFF 0xD00 0xD00 0xD40 - 0xD7F 0xD80 - 0xDFF
UART channel 6 Regs Reserved UART 6 - Read FIFO UART 6 - Write FIFO Reserved UART 6 - Read FIFO with errors
(Table 13 &
8/16/24/32
First 8 regs are 16550 compatible
Table 14)
Read-Only Write-Only 8/16/24/32 8/16/24/32 64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
0xE00 - 0xE0F 0xE10 - 0xEFF 0xF00 0xF00 0xF40 - 0xF7F 0xF80 - 0xFFF
UART channel 7 Regs Reserved UART 7 - Read FIFO UART 7 - Write FIFO Reserved UART 7 - Read FIFO with errors
(Table 13 &
8/16/24/32
First 8 regs are 16550 compatible
Table 14)
Read-Only Write-Only 8/16/24/32 8/16/24/32 64 bytes of RX FIFO data 64 bytes of TX FIFO data
Read-Only
16/32
64 bytes of RX FIFO data + LSR
16
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
1.6
Device Configuration Registers
The Device Configuration Registers provide easy programming of general operating parameters to the V258 and for monitoring the status of various functions. These registers control or report on all 8 channel UARTs functions that include interrupt control and status, 16-bit general purpose timer control and status, multipurpose inputs/outputs control and status, sleep mode control, soft-reset control, and device identification and revision, and others. Tables 6 and 7 below show these registers in BYTE and DWORD alignment. Each of these registers is described in detail in the following paragraphs.
TABLE 6: DEVICE CONFIGURATION REGISTERS SHOWN IN BYTE ALIGNMENT
ADDRESS [A7:A0] Ox080 Ox081 Ox082 Ox083 REGISTER INT0 [7:0] INT1 [15:8] INT2 [23:16] INT3 [31:24] READ/WRITE COMMENT Read-only Interrupt [7:0] Read-only Read-only Read-only
RESET STATE
Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00
Ox084 Ox085 Ox086 Ox087
TIMERCNTL TIMER TIMERLSB TIMERMSB
Read/Write Timer Control Reserved Read/Write Timer LSB Read/Write Timer MSB
Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0]= 0x00 Bits [7:0]= 0x00
Ox088 Ox089 Ox08A Ox08B
8XMODE REGA RESET SLEEP
Read/Write Reserved Write-only Self clear bits after executing Reset Read/Write Sleep mode
Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0]= 0x00
Ox08C Ox08D Ox08E Ox08F
DREV DVID REGB MPIOINT
Read-only Device revision Read-only Device identification Write-only Read/Write MPIO interrupt mask
Bits [7:0] = Current Rev. Bits [7:0] = 0x38 Bits [7:0] = 0x00 Bits [7:0] = 0x00
Ox090 Ox091 Ox092 Ox093
MPIOLVL MPIO3T MPIOINV MPIOSEL
Read/Write MPIO level control Read/Write MPIO output control Read/Write MPIO input polarity select Read/Write MPIO select
Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0xFF
17
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 7: DEVICE CONFIGURATION REGISTERS SHOWN IN DWORD ALIGNMENT
ADDRESS 0x080-083 0x084-087 0x088-08B 0x08C-08F 0x090-093 REGISTER INTERRUPT (read-only) TIMER (read/write) ANCILLARY1 (read/write) ANCILLARY2 (read-only) MPIO (read/write) BYTE 3 [31:24] INT3 TIMERMSB SLEEP MPIOINT MPIOSEL BYTE 2 [23:16] INT2 TIMERLSB RESET REGB MPIOINV BYTE 1 [15:8] INT1
xr
REV. 1.0.0
BYTE 0 [7:0] INT0 TIMERCNTL 8XMODE DREV MPIOLVL
TIMER (reserved) REGA DVID MPIO3T
1.6.1
The Global Interrupt Register
The XR17V258 has a 32-bit wide register [INT0, INT1, INT2 and INT3] to provide interrupt information and supports two interrupt schemes. The first scheme is an 8-bit indicator representing all 8 channels with each bit representing each channel from 0 to 7. This permits the interrupt service routine to quickly determine which UART channels need servicing so that it can go to the appropriate UART channel interrupt service routines. INT0 bit [0] represents the interrupt status for UART channel 0 when its transmitter, receiver, line status, or modem port status requires service. Other bits in the INT0 register provide indication for the other channels with bit [7] representing UART channel 7 respectively. The second scheme provides detail about the source of the interrupts for each UART channel. All the interrupts are encoded into a 3-bit code. This 3-bit code represents 7 interrupts corresponding to individual UART's transmitter, receiver, line status, modem port status. INT1, INT2 and INT3 registers provide the 24-bit interrupt status for all 8 channels. bits [10:8] representing channel 0 and bits [31:29] representing channel 7 respectively. All 8 channel interrupts status are available with a single DWORD read operation. This feature allows the host another method to quickly service the interrupts, thus reducing the service interval and host bandwidth requirement.
GLOBAL INTERRUPT REGISTER (DWORD)
INT3 [31:24] INT2 [23:16]
[default 0x00-00-00-00]
INT0 [7:0]
INT1 [15:8]
All bits start up zero. A special interrupt condition is generated by the V258 upon awakening from sleep after all eight channels were put to sleep mode earlier. Figure 5 shows the 4-byte interrupt register and its make up.
INT0 [7:0] Channel Interrupt Indicator
Each bit gives an indication of the channel that has requested for service. Bit [0] represents channel 0 and bit [7] indicates channel 7. Logic 1 indicates the channel N [7:0] has called for service. The interrupt bit clears after reading the appropriate register of the interrupting channel register, see Interrupt Clearing section.
The INT0 register provides individual status for each channel
INT0 Register Individual UART Channel Interrupt Status Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0 Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
INT3, INT2 and INT1 [32:8] Twenty four bit encoded interrupt indicator. Each channel's interrupt is encoded into 3 bits for receive, transmit, and status. bits [10:8] represent channel 0 and go up to channel 7 with bits [31:29]. The 3-bit encoding and their priority order are shown below in Table 8. The Timer and MPIO interrupts are for the device and therefore they exist within channel 0 space and not in other channel interrupt.
18
xr
REV. 1.0.0
.
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
FIGURE 5. THE GLOBAL INTERRUPT REGISTER, INT0, INT1, INT2 AND INT3
Interrupt Registers, INT0, INT1, INT2 and INT3
INT3 Register Channel-7 Bit N+2 Bit N+1 Bit N Channel-6 Bit N+2 Bit N+1 Bit N Channel-5 Bit N+2 Bit N+1 Bit N INT2 Register Channel-4 Bit N+2 Bit N+1 Bit N Channel-3 Bit N+2 Bit N+1 Bit N Channel-2 Bit N+2 Bit N+1 Bit N INT1 Register Channel-1 Bit N+2 Bit N+1 Bit N Channel-0 Bit N+2 Bit N+1 Bit N
INT0 Register Ch-7 Ch-6 Ch-5 Ch-4 Bit-7 Bit-6 Bit-5 Bit-4 Ch-3 Ch-2 Ch-1 Ch-0 Bit-3 Bit-2 Bit-1 Bit-0
TABLE 8: UART CHANNEL [7:0] INTERRUPT SOURCE ENCODING
PRIORITY x 1 2 3 4 5 6 7 BIT[N+2] 0 0 0 0 1 1 1 1 BIT[N+1] 0 0 1 1 0 0 1 1 BIT[N] 0 1 0 1 0 1 0 1 None or wake-up indicator RXRDY and RX Line Status (logic OR of LSR[4:1]) RXRDY Time-out TXRDY, THR or TSR (auto RS485 mode) empty MSR, RTS/CTS or DTR/DSR delta or Xoff/Xon det. or special char. detected Reserved. MPIO pin(s). Available only within channel 0, reserved in other channels. TIMER Time-out. Available only within channel 0, reserved in other channels. INTERRUPT SOURCE(S)
TABLE 9: UART CHANNEL [7:0] INTERRUPT CLEARING
Wake-up Indicator is cleared by reading the INT0 register. RXRDY and RXRDY Time-out is cleared by reading data in the RX FIFO until the RX FIFO is empty. RX Line Status interrupt clears after reading the LSR register that is in the UART channel register set. TXRDY interrupt clears after reading ISR register that is in the UART channel register set. Modem Status Register interrupt clears after reading MSR register that is in the UART channel register set. RTS/CTS or DTR/DSR delta interrupt clears after reading MSR register that is in the UART channel register set. Xoff/Xon delta and special character detect interrupt clears after reading the ISR register that is in the UART channel register set. TIMER Time-out interrupt clears after reading the TIMERCNTL register that is in the Device Configuration register set. MPIO interrupt clears after reading the MPIOLVL register that is in the Device Configuration register set.
19
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 1.6.2
xr
REV. 1.0.0
General Purpose 16-bit Timer/Counter [TIMERMSB, TIMELSB, TIMER, TIMECNTL] (DEFAULT 0XXX-XX-00-00)
The XR17V258 has a general purpose 16-bit timer/counter. The crystal/clock at the XTAL1 input or an external clock at the TMRCK input pin can be selected as the clock source for the timer/counter. The timer can be set to be a single-shot for a one-time event or re-triggerable for a periodic signal. An interrupt may be generated when the timer times out and will show up as a Channel 0 interrupt (see Table 8). It is controlled through 4 configuration registers [TIMERCNTL, TIMER, TIMELSB, TIMERMSB]. The TIMERCNTL register provides the Timer commands such as start/stop, as shown in Table 10 below. The time-out output of the Timer can also be optionally routed to the MPIO[0] pin. The block diagram of the Timer/Counter circuit is shown below:
FIGURE 6. TIMER/COUNTER CIRCUIT
TIM ERM SB and TIM ERLSB (16-bit Value)
TM RCK OSC. CLOCK 1 0
16-Bit Tim er/Counter
Tim er Output
1 0
M PIO[0]
Clock Select Start/Stop
M PIOLVL[0] Tim er Interrupt 1 0 Tim er Interrupt No Interrupt
TIM ERCNTL COM M ANDS Single shot/Re-triggerable
Tim er Interrupt Enable/ Disable Route/De-route to M PIO[0]
TIMERMSB [31:24] and TIMERLSB [23:16]
The concatentaion of the 8-bit registers TIMERMSB and TIMERLSB forms a 16-bit value which decides the time-out period of the Timer, per the following equation: Timer output frequency = Timer input clock / 16-bit Timer value The least-significant bit of the timer is being bit [0] of the TIMERLSB with most-significant-bit being bit [7] in TIMERMSB. Notice that these registers do not hold the current counter value when read. Default value is zero (timer disabled) upon powerup and reset. The 'Reset Timer' command does not have any effect on this register.
16-Bit Timer/Counter Programmable Registers
TIMERMSB Register Bit-15 Bit-14 Bit-13 Bit-12 Bit-11 Bit-10 Bit-9 Bit-8 Bit-7 Bit-6 TIMERLSB Register Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
TIMER [15:8] Reserved
20
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
TIMERCNTL [7:0] Register
The bits [3:0] of this register are used to issue commands. The commands are self-clearing, so reading this register does not show the last written command. Reading this register returns a value of 0x01 when the Timer interrupt is enabled and there is a pending Timer interrupt. It returns a value of 0x00 at all other times. The default settings of the Timer, upon power-up, a hardware reset or upon the issue of a 'Timer Reset' command are:

Timer Interrupt Disabled Re-triggerable mode selected Internal crystal oscillator outputs selected as clock source Timer output not routed to MPIO[0] Timer stopped
TABLE 10: TIMER CONTROL REGISTERS
TIMERCNTL [7:4] TIMERCNTL [3:0]
Reserved These bits are used to invoke a series of commands that control the function of the Timer/Counter. The commands 1100 to 1111 are reserved. 0001: Enable Timer Interrupt 0010: Disable Timer Interrupt 0011: Select One-shot mode 0100: Select Re-triggerable mode 0101: Select Internal Crystal Oscillator output as clock input for the Timer 0110: Select External Clock input through the TMRCK pin for the Timer 0111: Route Timer output to MPIO[0] pin 1000: De-route Timer output from MPIO[0] 1001: Start Timer 1010: Stop Timer 1011: Reset Timer
TIMER OPERATION
The following paragraphs describe the operation of the 16-bit Timer/Counter. The following conventions will be used in this discussion:

'N' is the 16-bit value programmed in the TIMER MSB, LSB registers P +Q = N, where 'P' and 'Q' are approximately half of 'N'. If N is even, P = Q = N/2. If N is odd, P = (N - 1)/2 and Q = (N + 1)/2. `N' can take any value from 0x0002 to 0xFFFF.
Timer Operation in One-Shot Mode:
In the one-shot mode, the Timer output will stay HIGH when started (default state) and will continue to stay HIGH until it times out (reaches the terminal count of `N' clocks), at which time it will become LOW and stay LOW. If the Timer is re-started before the Timer times out, the counter is reset and the Timer will wait for another time-out period before setting its output LOW (See Figure 7). If the Timer times out, re-starting the Timer does not have any effect and a 'Stop Timer' command needs to be issued first which will set the Timer output to its default HIGH state. The Timer must be programmed while it is stopped since the following operations are blocked after the Timer has been started:

Any write to TIMER MSB, LSB registers Issue of any command other than 'Start Timer', 'Stop Timer' and 'Reset Timer'
21
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT Timer Operation in Re-triggerable Mode:
xr
REV. 1.0.0
In the re-triggerable mode, when the Timer is started, the Timer output will stay HIGH until it reaches half of the terminal count N (= P clocks) and toggle LOW and stay LOW for a similar amount of time (Q clocks). The above step will keep repeating until the Timer is stopped at which time the output will become HIGH (default state). See Figure 7. Also, after the Timer is started, re-starting the Timer does not have any effect in retriggerable mode. The Timer must be programmed while it is stopped since the following operations are blocked when the Timer is running:

Any write to TIMER MSB, LSB registers Issue of any command other than 'Stop Timer' and 'Reset Timer' ('Start Timer' is not allowed)
Routing the Timer Output to MPIO[0] Pin:
MPIO[0] pin is by default (on power up or reset, for example) an input. However, whenever the Timer output is routed to MPIO[0] pin,

MPIO[0] will be automatically selected as an output MPIO[0] will become HIGH (the default state of Timer output) All MPIO control registers (MPIOLVL, MPIOSEL etc) lose control over MPIO[0] and get the control back only when the Timer output is de-routed from MPIO[0].
FIGURE 7. TIMER OUTPUT IN ONE-SHOT AND RE-TRIGGERABLE MODES
START TIMER COMMAND ISSUED START TIMER COMMANDS ISSUED: LESS THAN 'N' CLOCKS BETWEEN SUCCESSIVE COMMANDS START TIMER COMMAND ISSUED STOP TIMER COMMAND ISSUED
TIMER Output in One-Shot Mode
'N' Clocks
< 'N' Clocks
< 'N' Clocks
TIMER Output in Re-triggerable Mode
After 'P' clocks
After 'P' clocks
After 'P' clocks
After 'P' clocks
After 'P' clocks
After 'Q' clocks
After 'Q' clocks
After 'Q' clocks
After 'Q' clocks
Timer Interrupt
In the one-shot mode, the Timer will issue an interrupt upon timing out which is 'N' clocks after the Timer is started. In the re-triggerable mode, the Timer will keep issuing an interrupt every 'N' clocks which is on every rising edge of the Timer output. The Timer interrupt can be cleared by reading the TIMERCNTL register or when a Timer Reset command is issued which brings the Timer back to its default settings. The TIMERCNTL will read a value of 0x01 when the Timer interrupt is enabled and there is a pending interrupt. It reads a value of 0x00 at all other times. Stopping the Timer does not clear the interrupt and neither does subsequent restarting.
22
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
FIGURE 8. INTERRUPT OUTPUT (ACTIVE LOW) IN ONE-SHOT AND RE-TRIGGERABLE MODES
Timer Started Timer Timed Out TIMERCNTL read
One-shot Mode
Timer Timed TIMERCNTL Out read
Timer Timed Out
Re-triggerable Mode
1.6.3
8XMODE [7:0] (default 0x00)
Each bit selects 8X or 16X sampling rate for that UART channel, bit [0] is channel 0. Logic 0 (default) selects normal 16X sampling with logic one selects 8X sampling rate. Transmit and receive data rates will double by selecting 8X.
8XMODE Register Individual UART Channel 8X Clock Mode Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0
1.6.4 1.6.5
REGA [15:8] (default 0x00) Reserved RESET [23:16] (default 0x00)
The 8-bit Reset register [RESET] provides the software with the ability to reset the UART(s) when there is a need. Each bit is self-clearing after it is written a logic 1 to perform a reset to that channel. All registers in that channel will be reset to the default condition, see Table 21 for details. .
RESET Register Individual UART Channel Reset Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0
23
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 1.6.6 SLEEP [31:24] (default 0x00)
xr
REV. 1.0.0
SLEEP Register Individual UART Channel Sleep Enable Ch-7 Ch-6 Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0 Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
The 8-bit Sleep register enables each UART separately to enter Sleep mode. Sleep mode reduces power consumption when the system needs to put the UART(s) to idle. The UART enters sleep mode when the following conditions are satisfied after the sleep mode is enabled (Logic 0 (default) is to disable and logic 1 is to enable sleep mode):

There is no pending interrupt RX pin is idling at a HIGH in normal mode or a LOW in infrared mode The modem inputs (CTS#, DSR#, CD# and RI#) are steady at either HIGH or LOW (MSR bits [3:0] = 0x0)
When all 8 UART channels are put to sleep, the on-chip oscillator shuts off to further conserve power. In this case, the V258 is awakened by any of the following events occurring at any of the 8 UART channels:

A receive data start bit transition (HIGH to LOW in normal mode or from LOW to HIGH in infrared mode) A data byte is loaded into the transmitter A change of logic state on any of the modem inputs, i.e. any of the delta bits (MSR bits[7:4]) is set
The V258 is ready after 32 crystal clocks to ensure full functionality. Therefore, if the V258 is awakened by a receive data start bit transition, that character (and the subsequent few characters) may not be received correctly. Also, a special interrupt is generated with an indication of no pending interrupt. The V258 will return to sleep mode automatically after all interrupting conditions have been serviced and cleared. It will stay in the sleep mode of operation until it is disabled by resetting the SLEEP register bits.
1.6.7 Device Identification and Revision
There are two internal registers that provide device identification and revision, DVID and DREV registers. The 8-bit content in the DVID register provides device identification. A return value of 0x48 from this register indicates the device is a XR17V258. The DREV register returns an 8-bit value of 0x01 for revision A with 0x02 equals to revision B and so on. This information is very useful to the software driver for identifying which device it is communicating with and to keep up with revision changes.
DVID [15:8]
Device identification for the type of UART. The Device ID of the XR17V258 is 0x48.
DREV [7:0]
Revision number of the XR17V258. A 0x01 represents "revision-A" with 0x02 for rev-B and so on.
REGB [23:16] (default 0x00)
REGB register provides a control for simultaneous write to all 8 UARTs configuration register or individually. This is very useful for device initialization in the power up and reset routines. Also, the register provides a facility to interface to the non-volatile memory device such as a 93C46 EEPROM. In embedded applications, the user can use this facility to store proprietary data in an external EEPROM.
24
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
1.6.8
REGB Register
Logic 0 (default) write to each UART configuration registers individually. Logic 1 enables simultaneous write to all 8 UARTs configuration register.
REGB[16](Read/Write)
REGB[19:17] REGB[20] (Write-Only) REGB[21] (Write-Only) REGB[22] (Write-Only) REGB[23] (Read-Only)
Reserved Control the EECK, clock, output (pin 116) on the EEPROM interface. Control the EECS, chips select, output (pin 115) to the EEPROM device. EEDI (pin 114) data input. Write data to the EEPROM device. EEDO (pin 113) data output. Read data from the EEPROM device.
1.6.9
Multi-Purpose Inputs and Outputs
The V258 provides 8 multi-purpose inputs/outputs MPIO[7:0] for general use. Each pin can be programmed to be an input or output function. The input logic state can be set for normal or inverted level, and optionally set to generate an interrupt. The outputs can be set to be normal HIGH or LOW state, or 3-state. Their functions and definitions are programmed through 5 registers: MPIOINT, MPIOLVL, MPIO3T, MPIOINV and MPIOSEL. If all 8 pins are set for inputs, all 8 interrupts would be ORed together. The ORed interrupt is reported in the channel 0 UART interrupt status, see Interrupt Status Register. The pins may also be programmed to be outputs and to the 3-state condition for signal sharing. The MPIO[0] pin can be programmed to show the Timer output. When it is programmed to be the Timer output, all the above 5 registers lose control over the MPIO[0] pin. For details on Timer output, please see "Section 1.6.2, General Purpose 16-bit Timer/Counter [TIMERMSB, TIMELSB, TIMER, TIMECNTL] (default 0xXX-XX-00-00)" on page 20.
1.6.10 MPIO REGISTERS
There are 5 registers that select, control and monitor the 8 multipurpose inputs and outputs. Figure 9 shows the internal circuitry.
25
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT FIGURE 9. MULTIPURPOSE INPUT/OUTPUT INTERNAL CIRCUIT
MPIOINT [7:0]
xr
REV. 1.0.0
INT
AND
Rising Edge Detection
AND
1 MPIOLVL [7:0]
Read Input Level
MPIO Pin [7:0] 0
MPIOINV [7:0]
(Input Inversion Enable =1)
MPIOLVL [7:0]
(Output Level)
MPIO3T [7:0]
(3-state Enable =1) OR
MPIOSEL [7:0]
(Select Input=1, Output=0 ) MPIOCKT
MPIOINT [7:0] (default 0x00)
The MPIOINT register enables the multipurpose input pin interrupt. If an MPIO pin is selected by MPIOSEL as an input, then it can be selected to generate an interrupt. MPIOINT bit[0] enables input pin MPIO0 for interrupt, and bit [7] enables input pin 7. No interrupt is enable if the pin is selected to be an output. The interrupt is edge sensing and determined by MPIOINV and MPIOLVL registers. The MPIO interrupt clears after a read to register MPIOLVL. The combination of MPIOLVL and MPIOINV determines the interrupt being active LOW or active HIGH. Logic 0 (default) disables the pin's interrupt and logic 1 enables it.
MPIOINT Register Multipurpose Input/Output Interrupt Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
MPIO7 MPIO6 MPIO5 MPIO4 MPIO3 MPIO2 MPIO1 MPIO0
MPIOLVL [7:0] (default 0x00)
The MPIOLVL register controls the output pins and provides the input level status for the input pins. The status of the input pin(s) is read on this register and output pins are controlled on this register. A logic 0 (default) sets the output to LOW and a logic 1 sets the output pin to HIGH. The MPIO interrupt will clear upon reading this register.
26
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
MPIOLVL Register Multipurpose Output Level Control Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
MPIO7 MPIO6 MPIO5 MPIO4 MPIO3 MPIO2 MPIO1 MPIO0
MPIO3T [7:0] (default 0x00)
The MPIO outputs can be tri-stated by the MPIO3T register. A logic 0 (default) sets the output to active level per register MPIOBIT settling, a logic 1 sets the output pin to tri-state.
MPIO3T Register Multipurpose Output 3-state Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
MPIO7 MPIO6 MPIO5 MPIO4 MPIO3 MPIO2 MPIO1 MPIO0
MPIOINV [7:0] (default 0x00)
The MPIO inputs can be inverted by the MPIOINV register. A logic 0 (default) does not invert the input pin logic. A logic 1 inverts the input logic level.
MPIOINV Register Multipurpose Input Signal Inversion Enable Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
MPIO7 MPIO6 MPIO5 MPIO4 MPIO3 MPIO2 MPIO1 MPIO0
MPIOSEL [7:0] (default 0xFF)
The MPIOSEL register defines the MPIOs as either an input or output. A logic 1 (default) defines the pin for input and a logic 0 for output.
MPIOSEL Register Multipurpose Input/Output Selection Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
MPIO7 MPIO6 MPIO5 MPIO4 MPIO3 MPIO2 MPIO1 MPIO0
2.0 CRYSTAL OSCILLATOR / BUFFER
The V258 includes an on-chip oscillator (XTAL1 and XTAL2). The crystal oscillator provides the system clock to the Baud Rate Generators (BRG) in each of the 8 UARTs, the 16-bit general purpose timer/counter and internal logics. XTAL1 is the input to the oscillator or external clock buffer input with XTAL2 pin being the output. See the Programmable Baud Rate Generator in the UART section on page 31 for programming details. The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant with 10-22 pF capacitance load, 100ppm) connected externally between the XTAL1 and XTAL2 pins (see Figure 10). Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal 8 baud rate
27
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
generators for standard or custom rates. Typically, the oscillator connections are shown in Figure 10. For further reading on oscillator circuit please see application note DAN108 on EXAR's web site.
FIGURE 10. TYPICAL OSCILLATOR CONNECTIONS
R=300K to 400K
XTAL1
14.7456 MHz
XTAL2
C1 22-47pF
C2 22-47pF
3.0 TRANSMIT AND RECEIVE DATA
There are two methods to load transmit data and unload receive data from each UART channel. First, there is a transmit data register and receive data register for each UART channel as shown in Table 5 set to ease programming. These registers support 8, 16, 24 and 32 bits wide format. In the 32-bit format, it increases the data transfer rate on the PCI bus. Additionally, a special register location provides receive data byte with its associated error flags. This is a 16-bit or 32-bit read operation where the Line Status Register (LSR) content in the UART channel register is paired along with the data byte. This operation further facilitates data unloading with the error flags without having to read the LSR register separately. Furthermore, the XR17V258 supports PCI burst mode for read/write operation of up to 64 bytes of data. The second method is through each UART channel's transmit holding register (THR) and receive holding register (RHR). The THR and RHR registers are 16550 compatible so their access is limited to 8-bit format. The software driver must separately read the LSR content for the associated error flags before reading the data byte.
3.1 FIFO DATA LOADING AND UNLOADING IN 32-BIT FORMAT.
The XR17V258 supports PCI Burst Read and PCI Burst Write transactions anywhere in the mapped memory region (except reserved areas). In addition, to utilize this feature fully, the device provides a separate memory location (apart from the individual channel's register set) where the RX and the TX FIFO can be read from/ written to, as shown in Table 5. The following is an extract from the table showing the memory locations that support burst transactions: Channel N: (for channels 0 through 7) where M = 2N + 1. RX FIFO TX FIFO RX FIFO + status Channel 2: RX FIFO TX FIFO RX FIFO + status
3.1.1
: : :
0xM00 - 0xM3F (64 bytes) 0xM00 - 0xM3F (64 bytes) 0xM80 - 0xMFF (64 bytes data + 64 bytes status)
For example, the locations for channel 2 are: : : : 0x500 - 0x53F (64 bytes) 0x500 - 0x53F (64 bytes) 0x580 - 0x5FF (64 bytes data + 64 bytes status)
Normal Rx FIFO Data Unloading at locations 0x100, 0x300, 0x500, 0x700
The RX FIFO data (up to the maximum 64 bytes) can be read out in a single burst 32-bit read operation (maximum 16 DWORD reads) at memory locations 0x100 (channel 0), 0x300 (channel 1), 0x500
28
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
(channel 2),......., 0xF00 (channel 7). This operation is at least 16 times faster than reading the data in 64 separate 8-bit memory reads of RHR register (0x000 for channel 0, 0x200 for channel 1, 0x400 for channel 2,......, 0xE00 for channel 7).
READ RX FIFO, WITH NO ERRORS Read n+0 to n+3 Read n+4 to n+7 Etc. BYTE 3 FIFO Data n+3 FIFO Data n+7 BYTE 2 FIFO Data n+2 FIFO Data n+6 BYTE 1 FIFO Data n+1 FIFO Data n+5 BYTE 0 FIFO Data n+0 FIFO Data n+4
Channel 0 to 7 ReceiveData in 32-bit alignment through the Configuration Register Address 0x0100, 0x0300, 0x0500, 0x0700, 0x0900, 0x0B00, 0x0D00 and 0x0F00 Receive Data Byte n+3
B7 B6 B5 B4 B3 B2 B1 B0 B7
Receive Data Byte n+2
B6 B5 B4 B3 B2 B1 B0 B7
Receive Data Byte n+1
B6 B5 B4 B3 B2 B1 B0
Receive Data Byte n+0
B7 B6 B5 B4 B3 B2 B1 B0
PCI Bus Data Bit-31
PCI Bus Data Bit-0
3.1.2
Special Rx FIFO Data Unloading at locations 0x180, 0x380, 0x580, and 0x780
The XR17V258 also provides the same RX FIFO data along with the LSR status information of each byte sideby-side, at locations 0x180 (channel 0), 0x380 (channel 1), 0x580 (channel 2), ....., 0xF80 (channel 3). The entire RX data along with the status can be downloaded in a single PCI Burst Read operation of 32 DWORD reads. The Status and Data bytes must be read in 16 or 32 bits format to maintain data integrity. The following tables show this clearly.
READ RX FIFO, ERRORS BYTE 3 FIFO Data n+1 FIFO Data n+3 BYTE 2 LSR n+1 LSR n+3 BYTE 1 FIFO Data n+0 FIFO Data n+2 BYTE 0 LSR n+0 LSR n+2
WITH LSR
Read n+0 to n+1 Read n+2 to n+3 Etc
Channel 0 to 7 Receive Data with Line Status Register in a 32-bit alignment through the Configuration Register Address 0x0180, 0x0380, 0x0580, 0x0780, 0x0980, 0x0B80, 0x0D80 and 0x0F80 Receive Data Byte n+1
B7 B6 B5 B4 B3 B2 B1 B0
Line Status Register n+1
B7 B6 B5 B4 B3 B2 B1 B0
Receive Data Byte n+0
B7 B6 B5 B4 B3 B2 B1 B0
Line Status Register n+0
B7 B6 B5 B4 B3 B2 B1 B0
PCI Bus Data Bit-31
PCI Bus Data Bit-0
29
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 3.1.3
xr
REV. 1.0.0
Tx FIFO Data Loading at locations 0x100, 0x300, 0x500, 0x700, 0x900, 0xB00, 0xD00, 0xF00
The TX FIFO data (up to the maximum 64 bytes) can be loaded in a single burst 32-bit write operation (maximum 16 DWORD writes) at memory locations 0x100 (channel 0), 0x300 (channel 1), 0x500 (channel 2), ............, 0xD00 (channel 6) and 0xF00 (channel 7).
WRITE TX FIFO Write n+0 to n+3 Write n+4 to n+7 Etc. BYTE 3 FIFO Data n+3 FIFO Data n+7 BYTE 2 FIFO Data n+2 FIFO Data n+6 BYTE 1 FIFO Data n+1 FIFO Data n+5 BYTE 0 FIFO Data n+0 FIFO Data n+4
Channel 0 to 7 Transmit Data in 32-bit alignment through the Configuration Register Address 0x0100, 0x0300, 0x0500, 0x0700, 0x0900, 0x0B00, 0x0D00 and 0x0F00 Transmit Data Byte n+3
B7 B6 B5 B4 B3 B2 B1 B0
Transmit Data Byte n+2
B7 B6 B5 B4 B3 B2 B1 B0
Transmit Data Byte n+1
B7 B6 B5 B4 B3 B2 B1 B0
Transmit Data Byte n+0
B7 B6 B5 B4 B3 B2 B1 B0
PCI Bus Data Bit-31
PCI Bus Data Bit-0
3.2
FIFO DATA LOADING AND UNLOADING THROUGH THE UART CHANNEL REGISTERS, THR AND RHR IN 8-BIT FORMAT
The THR and RHR register address for channel 0 to channel 7 is shown in Table 11 below. The THR and RHR for each channel 0 to 7 are located sequentially at address 0x0000, 0x0200, 0x0400, 0x0600, 0x0800, 0x0A000, 0x0C00 and 0x0E00. Transmit data byte is loaded to the THR when writing to that address and receive data is unloaded from the RHR register when reading that address. Both THR and RHR registers are 16C550 compatible in 8-bit format, so each bus operation can only write or read in bytes.
30
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
TABLE 11: TRANSMIT AND RECEIVE DATA REGISTER IN BYTE FORMAT, 16C550 COMPATIBLE
THR and RHR Address Locations For CH0 to CH7 (16C550 Compatible) CH0 0x000 Write THR CH0 0x000 Read RHR CH1 0x200 Write THR CH1 0x200 Read RHR CH2 0x400 Write THR CH2 0x400 Read RHR CH3 0x600 Write THR CH3 0x600 Read RHR CH4 0x800 Write THR CH4 0x800 Read RHR CH5 0xA00 Write THR CH5 0xA00 Read RHR CH6 0xC00 Write THR CH6 0xC00 Read RHR CH7 0xE00 Write THR CH7 0xE00 Read RHR Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-7 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-6 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-5 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-4 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-3 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-2 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-1 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0 Bit-0
THRRHR1
4.0 UART
There are 8 UARTs channel [7:0] in the V258. Each has its own 64-byte of transmit and receive FIFO, a set of 16550 compatible control and status registers, and a baud rate generator for individual channel data rate setting. Eight additional registers per UART were added for the EXAR enhanced features.
4.1 Programmable Baud Rate Generator with Fractional Divisor
Each UART has its own Baud Rate Generator (BRG) with a prescaler for the transmitter and receiver. The prescaler is controlled by a software bit in the MCR register. The MCR register bit [7] sets the prescaler to divide the input crystal or external clock by 1 or 4. The output of the prescaler clocks to the BRG. The BRG further divides this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/ 16) to obtain a 16X or 8X sampling clock of the serial data rate. The sampling clock is used by the transmitter for data bit shifting and receiver for data sampling. The BRG divisor (DLL, DLM and DLD registers) defaults to a random value upon power up. Therefore, the BRG must be programmed during initialization to the operating data rate. The DLL and DLM registers provide the integer part of the divisor and the DLD register provides the fractional part of the divisor. Only the four lower bits of the DLD are implemented and they are used to select a value from 0 (for setting 0000) to 0.9375 or 15/16 (for setting 1111). Programming the Baud Rate Generator Registers DLL, DLM and DLD provides the capability for selecting the operating data rate. Table 12 shows the standard data rates available with a 14.7456 MHz crystal or external clock at 16X clock rate. If the pre-scaler is used (MCR bit [7] = 1), the output data rate will be 4 times less than that shown in Table 12. At 8X sampling rate, these data rates would double. Also, when using 8X sampling mode, please note that the bit-time will have a jitter (+/- 1/16) whenever the DLD is an odd number. When using a non-standard data rate crystal or external clock, the divisor value can be calculated with the following equation(s):
Required Divisor (decimal) = (XTAL1 clock frequency / prescaler) / (serial data rate x 16), WITH 8XMODE [7:0] IS 0 Required Divisor (decimal) = (XTAL1 clock frequency / prescaler / (serial data rate x 8), WITH 8XMODE [7:0] IS 1
31
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
The closest divisor that is obtainable in the V258 can be calculated using the following formula: ROUND( (Required Divisor - TRUNC (Required Divisor) )*16)/16 + TRUNC (Required Divisor), where DLM = TRUNC( Required Divisor) >> 8 DLL = TRUNC (Required Divisor) & 0xFF DLD = ROUND ( (Required Divisor-TRUNC(Required Divisor) )*16) In the formulas above, please note that: TRUNC (N) = Integer Part of N. For example, TRUNC (5.6) = 5. ROUND (N) = N rounded towards the closest integer. For example, ROUND (7.3) = 7 and ROUND (9.9) = 10.
FIGURE 11. BAUD RATE GENERATOR
To Other Channels
DLL, DLM and DLD Registers Prescaler Divide by 1 XTAL1 XTAL2 Crystal Osc/ Buffer Prescaler Divide by 4 MCR Bit-7=0 (default) Fractional Baud Rate Generator Logic MCR Bit-7=1 16X or 8X Sampling Rate Clock to Transmitter and Receiver
TABLE 12: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING
REQUIRED OUTPUT DATA RATE 400 2400 4800 9600 10000 19200 25000 28800 38400 50000 57600 75000 DIVISOR FOR 16x Clock (Decimal) 3750 625 312.5 156.25 150 78.125 60 52.0833 39.0625 30 26.0417 20 DIVISOR OBTAINABLE IN V258 3750 625 312 8/16 156 4/16 150 78 2/16 60 52 1/16 39 1/16 30 26 1/16 20 DLM PROGRAM VALUE (HEX) E 2 1 0 0 0 0 0 0 0 0 0 DLL PROGRAM VALUE (HEX) A6 71 38 9C 96 4E 3C 34 27 1E 1A 14 DLD PROGRAM VALUE (HEX)) 0 0 8 4 0 2 0 1 1 0 1 0 DATA ERROR RATE (%) 0 0 0 0 0 0 0 0.04 0 0 0.08 0
32
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
TABLE 12: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING
REQUIRED OUTPUT DATA RATE 100000 115200 153600 200000 225000 230400 250000 300000 400000 460800 500000 750000 921600 1000000 DIVISOR FOR 16x Clock (Decimal) 15 13.0208 9.7656 7.5 6.6667 6.5104 6 5 3.75 3.2552 3 2 1.6276 1.5 DIVISOR OBTAINABLE IN V258 15 13 9 12/16 7 8/16 6 11/16 6 8/16 6 5 3 12/16 3 4/16 3 2 1 10/16 1 8/16 DLM PROGRAM VALUE (HEX) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DLL PROGRAM VALUE (HEX) F D 9 7 6 6 6 5 3 3 3 2 1 1 DLD PROGRAM VALUE (HEX)) 0 0 C 8 B 8 0 0 C 4 0 0 A 8 DATA ERROR RATE (%) 0 0.16 0.16 0 0.31 0.16 0 0 0 0.16 0 0 0.16 0
4.2
Automatic Hardware (RTS/CTS or DTR/DSR) Flow Control Operation
Automatic hardware or RTS/DTR and CTS/DSR flow control is used to prevent data overrun to the local receiver FIFO and remote receiver FIFO. The RTS#/DTR# output pin is used to request remote unit to suspend/restart data transmission while the CTS#/DSR# input pin is monitored to suspend/restart local transmitter. The auto RTS/DTR and auto CTS/DSR flow control features are individually selected to fit specific application requirement and enabled through EFR bit[7:6] and MCR bit [2] for either RTS/CTS or DTR/DSR control signals. The auto RTS/DTR function must be started by asserting RTS/DTR# output pin (MCR bit [0] or bit [1] to logic 1) after it is enabled. Figure 12 below explains how it works. Two interrupts associated with RTS/DTR and CTS/DSR flow control have been added to give indication when RTS/DTR# pin or CTS/DSR# pin is de-asserted during operation. The RTS/DTR and CTS/DSR interrupts must be first enabled by EFR bit [4], and then enabled individually by IER bits [7:6], and chosen with MCR bit [2]. Automatic hardware flow control is selected by setting bits [7 (CTS): 6 (RTS)] of the EFR register to logic 1. If CTS# pin transitions from LOW to HIGH indicating a flow control request, ISR bit [5] will be set to logic 1, (if enabled via IER bit [7:6]), and the UART will suspend TX transmissions as soon as the stop bit of the character in process is shifted out. Transmission is resumed after the CTS# input returns to LOW, indicating more data may be sent.
33
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT FIGURE 12. AUTO RTS/DTR AND CTS/DSR FLOW CONTROL OPERATION
Local UART UARTA Receiver FIFO Trigger Reached Auto RTS Trigger Level Transmitter Auto CTS Monitor RXA TXB
xr
REV. 1.0.0
Remote UART UARTB Transmitter Auto CTS Monitor Receiver FIFO Trigger Reached Auto RTS Trigger Level
RTSA# TXA
CTSB# RXB
CTSA# Assert RTS# to Begin Transmission 1 ON 2 7 ON 3 8 OFF
RTSB#
RTSA# CTSB# TXB
OFF
10 11
ON ON
Data Starts 4 RXA FIFO INTA (RXA FIFO Interrupt) Receive RX FIFO Data Trigger Level 5
6
Suspend
Restart 9
RTS High Threshold
RTS Low Threshold
12
RX FIFO Trigger Level
RTSCTS1
The local UART (UARTA) starts data transfer by asserting -RTSA# (1). RTSA# is normally connected to CTSB# (2) of remote UART (UARTB). CTSB# allows its transmitter to send data (3). TXB data arrives and fills UARTA receive FIFO (4). When RXA data fills up to its receive FIFO trigger level, UARTA activates its RXA data ready interrupt (5) and continues to receive and put data into its FIFO. If interrupt service latency is long and data is not being unloaded, UARTA monitors its receive data fill level to match the upper threshold of RTS delay and de-assert RTSA# (6). CTSB# follows (7) and request UARTB transmitter to suspend data transfer. UARTB stops or finishes sending the data bits in its transmit shift register (8). When receive FIFO data in UARTA is unloaded to match the lower threshold of RTS delay (9), UARTA re-asserts RTSA# (10), CTSB# recognizes the change (11) and restarts its transmitter and data flow again until next receive FIFO trigger (12). This same event applies to the reverse direction when UARTA sends data to UARTB with RTSB# and CTSA# controlling the data flow.
4.3
Infrared Mode
Each UART in the V258 includes the infrared encoder and decoder compatible to the IrDA (Infrared Data Association) version 1.0. The input pin ENIR conveniently activates all 8 UART channels to start up in the infrared mode. This global control pin enables the MCR bit [6] function in every UART channel register. After power up or a reset, the software can overwrite MCR bit [6] if so desired. ENIR and MCR bit [6] also disable its receiver while the transmitter is sending data. This prevents the echoed data from going to the receiver. The global activation ENIR pin prevents the infrared emitter from turning on and drawing large amount of current while the system is starting up. When the infrared feature is enabled, the transmit data outputs, TX[7:0], would idle LOW. Likewise, the RX [7:0] inputs assume a LOW idle level. The infrared encoder sends out a 3/16 of a bit wide pulse for each "0" bit in the transmit data stream. This signal encoding reduces the on-time of the infrared LED, hence reduces the power consumption. See Figure 13 below.
34
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
The infrared decoder receives the input pulse from the infrared sensing diode on RX pin. Each time the decoder senses a light pulse, it returns a "0" to the data bit stream. The RX input signal may be inverted prior delivered to the input of the decoder via internal register setting. This option supports active LOW instead of normal active HIGH pulse from some infrared modules on the market.
FIGURE 13. INFRARED TRANSMIT DATA ENCODING AND RECEIVE DATA DECODING
Character Start Stop 1 1 0 1 1/2 Bit Time 3/16 Bit Time
IrEncoder-1
Data Bits 1 0 1 0 0
TX Data
0
Transmit IR Pulse (TX Pin) Bit Time
Receive IR Pulse (RX pin)
Bit Time 1/16 Clock Delay
RX Data
0 Start
1
0
1
0
0
11
0
1 Stop
IRdecoder-
Data Bits Character
4.4
Internal Loopback
Each UART channel provides an internal loopback capability for system diagnostic. The internal loopback mode is enabled by setting MCR register bit [4] to a logic 1. All regular UART functions operate normally. Figure 14 shows how the modem port signals are re-configured. Transmit data from the transmit shift register output is internally routed to the receive shift register input allowing the system to receive the same data that it was sending. The TX pin is held at HIGH or mark condition while RTS# and DTR# are de-asserted. The CTS#, DSR#, CD# and RI# inputs are ignored.
35
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT FIGURE 14. INTERNAL LOOP BACK
xr
REV. 1.0.0
VCC
Transmit Shift Register
MCR bit-4=1
TX [7:0]
Internal Bus Lines and Control Signals
Receive Shift Register
VCC
RX [7:0]
RTS# [7:0]
RTS#
Modem / General Purpose Control Logic
CTS# VCC DTR#
CTS# [7:0] DTR# [7:0]
DSR# OP1# RI# OP2# CD#
DSR# [7:0] RI# [7:0] CD# [7:0]
4.5
UART CHANNEL CONFIGURATION REGISTERS AND ADDRESS DECODING
The 8 sets of UART configuration registers are decoded using address lines A9 to A11 as shown below. Address lines A0 to A3 select the 16 registers in each channel. The first 8 registers are 16550 compatible with EXAR enhanced feature registers located on the upper 8 addresses.
A11 0 0 0 0 1 1 1 1
A10 0 0 1 1 0 0 1 1
A9 0 1 0 1 0 1 0 1
UART CHANNEL SELECTION 0 1 2 3 4 5 6 7
36
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 13: UART CHANNEL CONFIGURATION REGISTERS.
ADDRESS A3 A2 A1 A0
REGISTER
READ/WRITE
COMMENTS
16550 COMPATIBLE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 00 00 01 10 01 10 11 00 01 10 11 RHR - Receive Holding Register THR - Transmit Holding Register DLL - Divisor LSB DLM - Divisor MSB DLD - Divisor Fractional Part IER - Interrupt Enable Register ISR - Interrupt Status Register FCR - FIFO Control Register LCR - Line Control Register MCR - Modem Control Register LSR - Line Status Register MSR - Modem Status Register - Auto RS485 Delay SPR - Scratch Pad Register ENHANCED REGISTER 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 00 01 10 11 00 01 10 11 FCTR EFR - Enhanced Function Register TXCNT - Transmit FIFO Level Counter TXTRG - Transmit FIFO Trigger Level RXCNT - Receive FIFO Level Counter RXTRG - Receive FIFO Trigger Level Xoff-1 - Xoff Character 1 Xchar Xoff-2 - Xoff Character 2 Xon-1 - Xon Character 1 Xon-2 - Xon Character 2 Read/Write Read/Write Read-only Write-only Read-only Write-only Write-only Read-only Write-only Write-only Write-only Xon,Xoff Rcvd. Flags Read-only Write-only Read/Write Read/Write Read/Write Read/Write Read-only Write-only Read/Write Read/Write Read-only Read-only Write-only Read/Write LCR[7] = 0 LCR[7] = 1 LCR[7] = 1 LCR[7] = 1 LCR[7] = 0 LCR[7] = 0
37
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
TABLE 14: UART CHANNEL CONFIGURATION REGISTERS DESCRIPTION. SHADED BITS ARE ENABLED BY EFR BIT-4.
ADDRESS A3-A0 0000 0000 0000 0001 0010 0001 REG NAME RHR THR DLL DLM DLD IER READ/ WRITE R W R/W R/W R/W R/W BIT [7] BIT [7] BIT [7] BIT [7] BIT [7] 0 0/ CTS/ DSR# Int. Enable 0010 ISR R FIFOs Enable BIT [6] BIT [6] BIT [6] BIT [6] BIT [6] 0 0/ BIT [5] Bit [5] Bit [5] Bit [5] Bit [5] 0 0/ BIT [4] Bit [4] Bit [4] Bit [4] Bit [4] 0 0 BIT [3] Bit [3] Bit [3] Bit [3] Bit [3] Bit [3] Modem Status Int. Enable BIT [2] Bit [2] Bit [2] Bit [2] Bit [2] Bit [2] RX Line Status Int. Enable BIT[1] Bit [1] Bit [1] Bit [1] Bit [1] Bit [1] TX Empty Int. Enable BIT [0] Bit [0] Bit [0] Bit [0] Bit [0] Bit [0] RX Data Int. Enable
COMMENT
LCR[7]=0 LCR[7]=0 LCR[7]=1 LCR[7]=1 LCR[7]=1
RTS/ Xon/ DTR# Xoff/Sp. Int. Char. Int. Enable Enable FIFOs Enable 0/ DeltaFlow Cntl 0/ TX FIFO Trigger 0/ Xoff/special char 0/ TX FIFO Trigger
LCR[7]=0
INT Source Bit [3]
INT Source Bit [2]
INT Source Bit [1]
INT Source Bit [0]
LCR[7]=0
0010
FCR
W
RX FIFO RX FIFO Trigger Trigger
DMA Mode
TX FIFO RX FIFO Reset Reset
FIFOs Enable
LCR[7]=0
0011
LCR
R/W
Divisor Enable 0/ BRG Prescaler
Set TX Break 0/ IR Enable TSR Empty RI RS485 DLY-2 Bit [6] TRG Table Bit [0]
Set Par- Even Parity ity 0/ XonAny Internal Loopback Enable
Parity Stop Bits Enable (OP2)1 (OP1)1
Word Length Bit [1]
Word Length Bit [0]
0100
MCR
R/W
TX char RTS/ ImmediDTR ate Flow Sel
RTS# DTR# Pin Con- Pin Control trol
0101
LSR
R/W
RX FIFO ERROR CD RS485 DLY-3 Bit [7] TRG Table Bit [1]
THR Empty DSR RS485 DLY-1 Bit [5] Auto RS485 Enable
RX Break
RX RX ParRX RX Data Framing ity Error Overrun Ready Error Delta CD# Disable TX Bit [3] RTS/ DTR Hyst Bit [3] Delta RI# Disable RX Bit [2] RTS/ DTR Hyst Bit [2] Bit [1] RTS/ DTR Hyst Bit [1] Bit [0] RTS/ DTR Hyst Bit [0] User Data Delta DSR# Delta CTS#
0110
MSR MSR
R W R/W R/W
CTS RS485 DLY-0 Bit [4] Invert IR RX Input
0111 1000
SPR FCTR
38
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
TABLE 14: UART CHANNEL CONFIGURATION REGISTERS DESCRIPTION. SHADED BITS ARE ENABLED BY EFR BIT-4.
ADDRESS A3-A0 1001 REG NAME EFR READ/ WRITE R/W BIT [7] Auto CTS/ DSR Enable BIT [6] Auto RTS/ DTR Enable BIT [5] Special Char Select BIT [4] Enable IER [7:5], ISR [5:4], FCR[5:4], MCR[7:5], MCR[3:2], MSR[7:2] Bit [4] Bit [4] Bit [4] Bit [4] 0 Bit [4] Bit [4] Bit [4] Bit [4] BIT [3] Software Flow Cntl Bit [3] BIT [2] Software Flow Cntl Bit [2] BIT[1] Software Flow Cntl Bit [1] BIT [0] Software Flow Cntl Bit [0]
COMMENT
1010 1010 1011 1011 1100 1100 1101 1110 1111 NOTE:
TXCNT TXTRG RXCNT RXTRG XCHAR XOFF1 XOFF2 XON1 XON2
R W R W R W W W W
Bit [7] Bit [7] Bit [7] Bit [7] 0 Bit [7] Bit [7] Bit [7] Bit [7]
Bit [6] Bit [6] Bit [6] Bit [6] 0 Bit [6] Bit [6] Bit [6] Bit [6]
Bit [5] Bit [5] Bit [5] Bit [5] 0 Bit [5] Bit [5] Bit [5] Bit [5]
Bit [3] Bit [3] Bit [3] Bit [3]
Bit [2] Bit [2] Bit [2] Bit [2]
Bit [1] Bit [1] Bit [1] Bit [1]
Bit [0] Bit [0] Bit [0] Bit [0]
TX Xon TX Xoff Xon Det. Xoff Det. Self clear Indicator Indicator Indicator Indicator after read Bit [3] Bit [3] Bit [3] Bit [3] Bit-2 Bit-2 Bit-2 Bit-2 Bit [1] Bit [1] Bit [1] Bit [1] Bit [0] Bit [0] Bit [0] Bit [0]
MCR bits [3:2] (OP1 and OP2 outputs) are not available in the XR17V258. They are present for 16C550 compatibility during Internal loopback, see Figure 14.
4.6
Transmitter
The transmitter section comprises of a 64 bytes of FIFO, a byte-wide Transmit Holding Register (THR) and an 8-bit Transmit Shift Register (TSR). THR receives a data byte from the host (non-FIFO mode) or a data byte from the FIFO when the FIFO is enabled by FCR bit [0]. TSR shifts out every data bit with the 16X or 8X internal clock. A bit time is 16 or 8 clock periods. The transmitter sends the start bit followed by the number of data bits, inserts the proper parity bit if enable, and adds the stop bit(s). The status of the THR and TSR are reported in the Line Status Register (LSR bit [6:5]).
4.6.1 Transmit Holding Register (THR)
The transmit holding register is an 8-bit register providing a data interface to the host processor. The host writes transmit data byte to the THR to be converted into a serial data stream including start-bit, data bits, parity-bit and stop-bit(s). The least-significant-bit (bit [0]) becomes first data bit to go out. The THR is also the input register to the transmit FIFO of 64 bytes when FIFO operation is enabled by FCR bit[0]. A THR empty interrupt can be generated when it is enabled in IER bit [1].
4.6.2 Transmitter Operation in non-FIFO Mode
The host loads transmit data to THR one character at a time. The THR empty flag (LSR bit [5]) is set when the data byte is transferred to TSR. THR flag can generate a transmit empty interrupt (ISR bit [1]) when it is enabled by IER bit [1]. The TSR flag (LSR bit [6]) is set when TSR becomes completely empty.
39
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT FIGURE 15. TRANSMITTER OPERATION IN NON-FIFO MODE
xr
REV. 1.0.0
Data Byte
Transmit Holding Register (THR)
THR Interrupt (ISR bit-1) Enabled by IER bit-1
16X or 8X Clock (8XMODE Register)
Transmit Shift Register (TSR)
M S B
L S B
TXNOFIFO1
4.6.3
Transmitter Operation in FIFO Mode
The host may fill the transmit FIFO with up to 64 bytes of transmit data. The THR empty flag (LSR bit [5]) is set whenever the FIFO is empty. The THR empty flag can generate a transmit empty interrupt (ISR bit [1]) when the amount of data in the FIFO falls below its programmed trigger level (see TXTRG register). The transmit empty interrupt is enabled by IER bit [1]. The TSR flag (LSR bit [6]) is set when TSR becomes completely empty. Furthermore, with the RS485 half-duplex direction control enabled (FCTR bit [5]=1) the source of the transmit empty interrupt changes to TSR empty instead of THR empty. This is to ensure the RTS# output is not changed until the last stop bit of the last character is shifted out.
4.6.4 Auto RS485 Operation
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by FCTR bit [5]. It de-asserts RTS# or DTR# after a specified delay indicated in MSR[7:4] following the last stop bit of the last character that has been transmitted. This helps in turning around the transceiver to receive the remote station's response. The delay optimizes the time needed for the last transmission to reach the farthest station on a long cable network before switching off the line driver. This delay prevents undesirable line signal disturbance that causes signal degradation. It also changes the transmitter empty interrupt to TSR empty instead of THR empty.
FIGURE 16. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE
Transmit Data Byte
Transmit FIFO (64-Byte)
Flow Control Characters (Xoff1/2 and Xon1/2 Reg. Auto Software Flow Control
THR Interrupt (ISR bit-1) falls below Programmed Trigger Level (TXTRG) and then when becomes empty. FIFO is Enabled by FCR bit-0=1
16X or 8X Clock (8XMODE Register) Auto CTS Flow Control (CTS# pin)
Transmit Data Shift Register (TSR)
TXFIFO1
40
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
4.7
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and Receive Holding Register (RHR). The RSR uses the 16X or 8X clock for timing. It verifies and validates every bit on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit, an internal receiver counter starts counting at the 16X or 8X clock rate. After 8 or 4 clocks the start bit period should be at the center of the start bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating the start bit in this manner prevents the receiver from assembling a false character. The rest of the data bits and stop bits are sampled and validated in this same manner to prevent false framing. If there were any error(s), they are reported in the LSR register bits [4:1]. Upon unloading the receive data byte from RHR, the receive FIFO pointer is bumped and the error flags are immediately updated to reflect the status of the data byte in RHR register. RHR can generate a receive data ready interrupt upon receiving a character or delay until it reaches the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready time-out function when receive data does not reach the receive FIFO trigger level. This time-out delay is 4 word lengths as defined by LCR bits [1:0] plus 12 bits time. The RHR interrupt is enabled by IER bit [0].
4.7.1 Receiver Operation in non-FIFO Mode FIGURE 17. RECEIVER OPERATION IN NON-FIFO MODE
16X or 8X Clock (8XMODE Register)
Receive Data Shift Register (RSR)
Data Bit Validation
Receive Data Characters
Receive Data Byte and Errors
Error Flags in LSR bits 4:2
Receive Data Holding Register (RHR)
RHR Interrupt (ISR bit-2)
RXFIFO1
4.7.2
Receiver Operation with FIFO
FIGURE 18. RECEIVER OPERATION IN FIFO AND FLOW CONTROL MODE
16X or 8X Sampling Clock (8XMODE Reg.)
Receive Data Shift Register (RSR)
Data Bit Validation
Receive Data Characters
64 bytes by 11bit wide FIFO
Example: - FIFO trigger level set at 48 bytes - RTS/DTR hyasteresis set at +/-8 chars. Data falls to 40 RTS#/DTR# re-asserts when data falls below Error Flags (64-sets)
the trigger level to restart remote transmitter. Enable by EFR bit-6=1, MCR bit-2. RHR Interrupt (ISR bit-2) is programmed at FIFO trigger level (RXTRG). FIFO is Enable by FCR bit-0=1
Receive Data FIFO (64-byte)
FIFO Trigger=48
Data fills to 56 Error Flags in LSR bits 4:2
RTS#/DTR# de-asserts when data fills above the trigger level to suspend remote transmitter. Enable by EFR bit-6=1, MCR bit-2.
Receive Data Byte and Errors
Receive Data
RXFIFO1
41
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 5.0 UART CONFIGURATION REGISTERS 5.1 5.2 5.3 Receive Holding Register (RHR) - Read only Transmit Holding Register (THR) - Write only Baud Rate Generator Divisors (DLM, DLL and DLD) SEE"RECEIVER" ON PAGE 41. SEE"TRANSMITTER" ON PAGE 39.
xr
REV. 1.0.0
The Baud Rate Generator (BRG) generates the data rate for the transmitter and receiver. The rate is programmed through registers DLM, DLL and DLD which are only accessible when LCR bit [7] is set to logic 1. Refer to "Section 4.1, Programmable Baud Rate Generator with Fractional Divisor" on page 31 for more details.
5.4 Interrupt Enable Register (IER) - Read/Write
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR) and also encoded in INT (INT0-INT3) register in the Device Configuration Registers.
5.4.1 IER versus Receive FIFO Interrupt Mode Operation
When the receive FIFO (FCR bit [0] = logic 1) and receive interrupts (IER bit [0] = logic 1) are enabled, the RHR interrupts (see ISR bits [4:3]) status will reflect the following:
A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed trigger level. It will be cleared when the FIFO drops below the programmed trigger level. B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register status bit and the interrupt will be cleared when the FIFO drops below the trigger level. C. The receive data ready bit (LSR bit [0]) is set as soon as a character is transferred from the shift register to the receive FIFO. It is reset when the FIFO is empty. 5.4.2 IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR bit [0] equals a logic 1 for FIFO enable; resetting IER bits [3:0] enables the XR16V258 in the FIFO polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either can be used in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR (non-FIFO mode) or RX FIFO (FIFO mode). B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid. C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any. D. LSR BIT-5 indicates THR (non-FIFO mode) or TX FIFO (FIFO mode) is empty. E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty. F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO. IER[7]: CTS# Input Interrupt Enable (requires EFR bit [4]=1)
* Logic 0 = Disable the CTS# interrupt (default). * Logic 1 = Enable the CTS# interrupt. The UART issues an interrupt when CTS# pin makes a transition from
LOW to HIGH.
IER[6]: RTS# Output Interrupt Enable (requires EFR bit [4]=1)
* Logic 0 = Disable the RTS# interrupt (default). * Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when RTS# pin makes a transition from
LOW to HIGH.
IER[5]: Xoff Interrupt Enable (requires EFR bit [4]=1)
* Logic 0 = Disable the software flow control, receive Xoff interrupt (default). * Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for
details.
42
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
IER[4]: Reserved IER[3]: Modem Status Interrupt Enable
The Modem Status Register interrupt is issued whenever any of the delta bits of the MSR register (bits [3:0]) is set.
* Logic 0 = Disable the modem status register interrupt (default). * Logic 1 = Enable the modem status register interrupt.
IER[2]: Receive Line Status Interrupt Enable
An Overrun error, Framing error, Parity error or detection of a Break character will result in an LSR interrupt. The V258 will issue an LSR interrupt immediately after receiving a character with an error. It will again re-issue the interrupt (if the first one has been cleared by reading the LSR register) when the character with the error is on the top of the FIFO, meaning the next one to be read out of the FIFO. For example, let's consider an incoming data stream of 0x55, 0xAA, etc. and that the character 0xAA has a Parity error associated with it. Let's assume that the character 0x55 has not been read out of the FIFO yet. The V258v258 will issue an interrupt as soon as the stop bit of the character 0xAA is received. The LSR register will have only the FIFO error bit (bit [7]) set and none of the other error bits (bits [4:1]) will be set, since the byte on the top of the FIFO is 0x55 which does not have any errors associated with it. When this byte has been read out, the V258 will issue another LSR interrupt and this time the LSR register will show the Parity bit (bit [2]) set.
* Logic 0 = Disable the receiver line status interrupt (default). * Logic 1 = Enable the receiver line status interrupt.
IER[1]: TX Ready Interrupt Enable
In non-FIFO mode, a TX interrupt is issued whenever the THR is empty. In the FIFO mode, an interrupt is issued twice: once when the number of bytes in the TX FIFO falls below the programmed trigger level and again when the TX FIFO becomes empty. When autoRS485 mode is enabled (FCTR bit [5] = 1), the second interrupt is delayed until the transmitter (both the TX FIFO and the TX Shift Register) is empty.
* Logic 0= Disable Transmit Ready Interrupt (default). * Logic 1 = Enable Transmit Ready Interrupt.
IER[0]: RX Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when the receive FIFO has reached the programmed trigger level in the FIFO mode.
* Logic 0 = Disable the receive data ready interrupt (default). * Logic 1 = Enable the receiver data ready interrupt.
5.5 Interrupt Status Register (ISR) - Read Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the ISR will give the user the current highest pending interrupt level to be serviced, others queue up for next service. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt Source Table, Table 15, shows the data values (bit [5:0]) for the six prioritized interrupt levels and the interrupt sources associated with each of these interrupt levels.
43
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 5.5.1 Interrupt Generation:
xr
REV. 1.0.0
* LSR is by any of the LSR bits [4:1]. See IER bit [2] description on the previous page. * RXRDY is by RX trigger level. * RXRDY Time-out is by a 4-char plus 12 bits delay timer. * TXRDY is by TX trigger level or TX FIFO empty (or transmitter empty in auto RS-485 control). * MSR is by any of the MSR bits [3:0]. * Receive Xoff/Special character is by detection of a Xoff or Special character. * CTS#/DSR# is when its transmitter toggles the input pin (from LOW to HIGH) during auto CTS/DSR flow
control enabled by EFR bit [7] and selection on MCR bit [2].
* RTS#/DTR# is when its receiver toggles the output pin (from LOW to HIGH) during auto RTS/DTR flow
control enabled by EFR bit [6] and selection on MCR bit [2].
5.5.2 Interrupt Clearing:
* LSR interrupt is cleared by a read to the LSR register. * RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level. * RXRDY Time-out interrupt is cleared by reading RHR. * TXRDY interrupt is cleared by a read to the ISR register or writing to THR. * MSR interrupt is cleared by a read to the MSR register. * Xoff interrupt is cleared by a read to ISR or when Xon character(s) is received. * Special character interrupt is cleared by a read to ISR or after the next character is received. * RTS#/DTR# and CTS#/DSR# status change interrupts are cleared by a read to the MSR register.
]
TABLE 15: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY LEVEL 1 2 3 4 5 6 7 X BIT [5] 0 0 0 0 0 0 1 0 ISR REGISTER STATUS BITS BIT [4] 0 0 0 0 0 1 0 0 BIT [3] 0 0 1 0 0 0 0 0 BIT [2] 1 1 1 0 0 0 0 0 BIT [1] 1 0 0 1 0 0 0 0 BIT [0] 0 0 0 0 0 0 0 1 LSR (Receiver Line Status Register) RXRDY (Received Data Ready) RXRDY (Receive Data Time-out) TXRDY (Transmitter Holding Register Empty) MSR (Modem Status Register) RXRDY (Received Xon/Xoff or Special character) CTS#/DSR#, RTS#/DTR# change of state None (default) or wake-up indicator SOURCE OF THE INTERRUPT
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are enabled.
ISR[5:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Table 15). See "Section 5.5.1, Interrupt Generation:" on page 44 and "Section 5.5.2, Interrupt Clearing:" on page 44 for details.
44
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
ISR[0]: Interrupt Status
* Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
* Logic 1 = No interrupt pending. (default condition)
5.6 FIFO Control Register (FCR) - Write Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1) The FCTR bits [5:4] are associated with these 2 bits. These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the trigger level. Table 16 shows the complete selections. Note that the receiver and the transmitter cannot use different trigger tables. Whichever selection is made last applies to both the RX and TX side.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = 1) The FCTR bits [7:6] are associated with these 2 bits by selecting one of the four tables. The 4 user selectable trigger levels in 4 tables are supported for compatibility reasons. These 2 bits set the trigger level for the transmit FIFO interrupt. The UART will issue a transmit interrupt when the number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the FIFO did not get filled over the trigger level on last re-load. Table 16 below shows the selections.
FCR[3]: DMA Mode Select
This bit has no effect since TXRDY and RXRDY pins are not available in this device. It is provided for legacy software compatibility.
* Logic 0 = Set DMA to mode 0 (default). * Logic 1 = Set DMA to mode 1.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit [0] is active.
* Logic 0= No transmit FIFO reset (default). * Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit [0] is active.
* Logic 0 = No receive FIFO reset (default). * Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[0]: TX and RX FIFO Enable
* Logic 0 = Disable the transmit and receive FIFO (default). * Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
45
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
TABLE 16: TRANSMIT AND RECEIVE FIFO TRIGGER TABLE AND LEVEL SELECTION
TRIGGER TABLE Table-A FCTR FCTR FCR FCR FCR FCR RECEIVE BIT [7] BIT [6] BIT [7] BIT [6] BIT [5] BIT [4] TRIGGER LEVEL 0 0 0 0 1 1 Table-B 0 1 0 1 0 1 0 0 1 1 0 0 1 1 Table-C 1 0 0 1 0 1 0 0 1 1 0 0 1 1 Table-D 1 1 X 0 1 0 1 X X X 0 1 0 1 8 16 56 60 Programmable Programmable 16L2752, 16L2750, via RXTRG via TXTRG 16C2852, 16C850, 16C854, 16C864 register register 0 1 0 1 8 16 24 28 8 16 32 56 16C654 0 0 1 (default) 4 8 14 16 8 24 30 TRANSMIT TRIGGER LEVEL 1 (default) COMPATIBILITY 16C550, 16C2550, 16C2552, 16C554, 16C580, 16L580
16C650A, 16L651
5.7
Line Control Register (LCR) - Read/Write
The Line Control Register is used to specify the asynchronous data communication format. The word or character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this register.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL, DLM, DLD) enable.
* Logic 0 = Data registers are selected (default). * Logic 1 = Divisor latch registers (DLL, DLM and DLD) are selected.
LCR[6]: Transmit Break Enable
When enabled the Break control bit causes a break condition to be transmitted (the TX output is forced to a "space", LOW, state). This condition remains until disabled by setting LCR bit [6] to a logic 0.
* Logic 0 = No TX break condition. (default) * Logic 1 = Forces the transmitter output (TX) to a "space", LOW, for alerting the remote receiver of a line
break condition.
46
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR bit [5] selects the forced parity format.
* LCR bit [5] = logic 0, parity is not forced (default). * LCR bit [5] = logic 1 and LCR bit [4] = logic 0, parity bit is forced to a logical 1for the transmit and receive
data.
* LCR bit [5] = logic 1 and LCR bit [4] = logic 1, parity bit is forced to a logical 0 for the transmit and receive
data.
TABLE 17: PARITY PROGRAMMING
LCR BIT [5] X 0 0 1 1 LCR BIT [4] X 0 1 0 1 LCR BIT [3] 0 1 1 1 1 PARITY SELECTION No parity Odd parity Even parity Force parity to mark, "1" Forced parity to space, "0"
LCR[4]: TX and RX Parity Select
If the parity bit is enabled with LCR bit [3] set to a logic 1, LCR bit [4] selects the even or odd parity format.
* Logic 0 = ODD Parity is generated by forcing an odd number of logic 1's in the transmitted character. The
receiver must be programmed to check the same format (default).
* Logic 1 = EVEN Parity is generated by forcing an even the number of logic 1's in the transmitted character.
The receiver must be programmed to check the same format.
LCR[3]: TX and RX Parity Select
Parity or no parity can be selected via this bit. The parity bit is a simple way used in communications for data integrity check. See Table 17 above for parity selection summary.
* Logic 0 = No parity. * Logic 1 = A parity bit is generated during the transmission while the receiver checks for parity error of the
data character received.
LCR[2]: TX and RX Stop-bit Length Select
The length of stop bit is specified by this bit in conjunction with the programmed word length.
BIT [2] 0 1 1 WORD
LENGTH
STOP BIT LENGTH (BIT TIME(S)) 1 (default) 1-1/2 2
5,6,7,8 5 6,7,8
LCR[1:0]: TX and RX Word Length Select
These two bits specify the word length to be transmitted or received.
BIT [1] 0 0 1 1 BIT [0] 0 1 0 1 WORD LENGTH 5 (default) 6 7 8
47
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 5.8 Modem Control Register (MCR) - Read/Write
xr
REV. 1.0.0
The MCR register is used for controlling the modem interface signals or general purpose inputs/outputs.
MCR[7]: Clock Prescaler Select
* Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
* Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
MCR[6]: Infrared Encoder/Decoder Enable
The state of this bit depends on the sampled logic level of pin ENIR during power up, following a hardware reset (rising edge of RST# input). Afterward user can override this bit for desired operation.
* Logic 0 = Enable the standard modem receive and transmit character interface. * Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. While in this mode, the TX/RX output/
input are routed to the infrared encoder/decoder. The data input and output levels will conform to the IrDA infrared interface requirement. As such, while in this mode the infrared TX output will be a LOW during idle data conditions. FCTR bit [4] may be selected to invert the RX input signal level going to the decoder for infrared modules that provide rather an inverted output.
MCR[5]: Xon-Any Enable
* Logic 0 = Disable Xon-Any function (default). * Logic 1 = Enable Xon-Any function. In this mode any RX character received will enable Xon, resume data
transmission.
MCR[4]: Internal Loopback Enable
* Logic 1 = Disable loopback mode (default). * Logic 1 = Enable local loopback mode, see loopback section and Figure 14.
MCR[3]: Send Char Immediate (OP2 in Local Loopback Mode)
This bit is used to transmit a character immediately irrespective of the bytes currently in the transmit FIFO. The data byte must be loaded into the transmit holding register (THR) immediately following the write to this bit (to set it to a '1'). In other words, no other register must be accessed between setting this bit and writing to the THR. The loaded byte will be transmitted ahead of all the bytes in the TX FIFO, immediately after the character currently being shifted out of the transmit shift register is sent out. The existing line parameters (parity, stop bits) will be used when composing the character. This bit is self clearing, therefore, must be set before sending a custom character each time. Please note that the Transmitter must be enabled for this function (MSR[3] = 0). Also, if software flow control is enabled, the software flow control characters (Xon, Xoff) have higher priority and will get shifted out before the custom byte is transmitted.
* Logic 0 = Send Char Immediate disabled (default). * Logic 1 = Send Char Immediate enabled.
In Local Loopback Mode (MCR[4] = 1), this bit acts as the legacy OP2 output and controls the CD bit in the MSR register as shown in Figure 14. Please make sure that this bit is a '0' when exiting the Local Loopback Mode.
MCR[2]: DTR# or RTS# for Auto Flow Control (OP1 in Local Loopback Mode)
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by EFR bit [6]. DTR# selection is associated with DSR# and RTS# is with CTS#.
* Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control. * Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
In Local Loopback mode (MCR[4] = 1), this bit acts as the legacy OP1 output and controls the RI bit in the MSR register, as shown in Figure 14.
48
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
MCR[1]: RTS# Output
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit [6] and MCR bit [2]=0. If the modem interface is not used, this output may be used for general purpose.
* Logic 0 = Force RTS# output to a HIGH (default). * Logic 1= Force RTS# output to LOW.
MCR[0]: DTR# Output
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit [6] and MCR bit [2]=1. If the modem interface is not used, this output may be used for general purpose.
* Logic 0 = Force DTR# output to a HIGH (default). * Logic 1 = Force DTR# output to a LOW.
5.9 Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit [2] is set to a logic 1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity, framing, overrun, break).
LSR[7]: Receive FIFO Data Error Flag
* Logic 0 = No FIFO error (default). * Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or
break indication is in the FIFO data. This bit clears when there are no more errors in the FIFO.
LSR[6]: Transmitter Empty Flag
This bit is the Transmitter Empty indicator. This bit is set to a logic 1 whenever both the transmit FIFO (or THR, in non-FIFO mode) and the transmit shift register (TSR) are both empty. It is set to logic 0 whenever either the TX FIFO or TSR contains a data character.
LSR[5]: Transmit FIFO Empty Flag
This bit is the Transmit FIFO Empty indicator. This bit indicates that the transmitter is ready to accept a new character for transmission. This bit is set to a logic HIGH when the last data byte is transferred from the transmit FIFO to the transmit shift register. The bit is reset to logic 0 as soon as a data byte is loaded into the transmit FIFO. In the non-FIFO mode this bit is set when the transmit holding register (THR) is empty; it is cleared when at a byte is written to the THR.
LSR[4]: Receive Break Flag
* Logic 0 = No break condition (default). * Logic 1 = The receiver received a break signal (RX was LOW for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO. The break indication remains until the RX input returns to the idle condition, "mark" or HIGH.
LSR[3]: Receive Data Framing Error Flag
* Logic 1 = No framing error (default). * Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[2]: Receive Data Parity Error Flag
* Logic 0 = No parity error (default). * Logic 1 = Parity error. The receive character in RHR (top of the FIFO) does not have correct parity
information and is suspect. This error is associated with the character available for reading in RHR.
49
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT LSR[1]: Receiver Overrun Flag
xr
REV. 1.0.0
* Logic 0 = No overrun error (default). * Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[0]: Receive Data Ready Indicator
* Logic 0 = No data in receive holding register or FIFO (default). * Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
5.10 Modem Status Register (MSR) - Read Only
This register provides the current state of the modem interface signals, or other peripheral device that the UART is connected. Lower four bits of this register are used to indicate the changed information. These bits are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general purpose inputs/outputs when they are not used with modem signals.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit [3] in the MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
MSR[6]: RI Input Status
Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit [2] in the MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[5]: DSR Input Status
DSR# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=1). Auto CTS/DSR flow control allows starting and stopping of local data transmissions based on the modem DSR# signal. A HIGH on the DSR# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW will resume data transmission. Normally MSR bit [5] is the complement of the DSR# input. However in the loopback mode, this bit is equivalent to the DTR# bit in the MCR register. The DSR# input may be used as a general purpose input when the modem interface is not used.
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=0). Auto CTS/DSR flow control allows starting and stopping of local data transmissions based on the modem CTS# signal. A HIGH on the CTS# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW will resume data transmission. Normally MSR bit [4] is the complement of the CTS# input. However in the loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input may be used as a general purpose input when the modem interface is not used.
MSR[3]: Delta CD# Input Flag
* Logic 0 = No change on CD# input (default). * Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit [3]).
MSR[2]: Delta RI# Input Flag
* Logic 0 = No change on RI# input (default). * Logic 1 = The RI# input has changed from a LOW to a HIGH, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit [3]).
50
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
MSR[1]: Delta DSR# Input Flag
* Logic 0 = No change on DSR# input (default). * Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit [3]).
MSR[0]: Delta CTS# Input Flag
* Logic 0 = No change on CTS# input (default). * Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit [3]).
5.11 Modem Status Register (MSR) - Write Only
The upper four bits [7:4] of this register set the delay in number of bits time for the auto RS-485 turn around from transmit to receive.
MSR [7:4]
When Auto RS485 feature is enabled (FCTR bit [5]=1) and RTS# output is connected to the enable input of a RS-485 transceiver. These 4 bits select from 0 to 15 bit-time delay after the end of the last stop-bit of the last transmitted character. This delay controls when to change the state of RTS# output. This delay is very useful in long-cable networks. Table 18 shows the selection. The bits are enabled by EFR bit [4].
TABLE 18: AUTO RS485 HALF-DUPLEX DIRECTION CONTROL DELAY FROM TRANSMIT-TO-RECEIVE
MSR[7] 0 0 0 0 0 9 0 0 1 1 1 1 1 1 1 1 MSR[6] 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 MSR[5] 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 MSR[4] 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 DELAY IN DATA BIT(S) TIME 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
51
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT MSR [3]: Transmitter Disable
xr
REV. 1.0.0
This bit can be used to disable the transmitter by halting the Transmit Shift Register (TSR). When this bit is set to a logic 1, the bytes already in the FIFO will not be sent out. Also, any more data loaded into the FIFO will stay in the FIFO and will not be sent out. When this bit is set to a logic 0, the bytes currently in the TX FIFO will be sent out. Please note that setting this bit to a logic 1 stops any character from going out. Also, this bit must be a logic 0 for the Send Char Immediate function (see MCR[3]).
* Logic 0 = Enable Transmitter (default). * Logic 1 = Disable Transmitter.
MSR [2]: Receiver Disable
This bit can be used to disable the receiver by halting the Receive Shift Register (RSR). When this bit is set to a logic 1, the receiver will operate in one of the following ways:

If a character is being received at the time of setting this bit, that character will be correctly received. No more characters will be received. If the receiver is idle at the time of setting this bit, one character will still be received fully. No more characters will be received.
The receiver can be enabled and will start receiving characters by resetting this bit to a logic 0. The receiver will operate in one of the following ways:

If the receiver is idle (RX pin is HIGH) at the time of setting this bit, the next character will be received normally. It is recommended that the receiver be idle when resetting this bit to a logic 0. If the receiver is not idle (RX pin is toggling) at the time of setting this bit, the RX FIFO will be filled with unknown data.
Any data that is in the RX FIFO can be read out at any time whether the receiver is disabled or not.
* Logic 0 = Enable Receiver (default). * Logic 1 = Disable Receiver.
MSR [1:0]: Reserved 5.12 SCRATCH PAD REGISTER (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
5.13 FEATURE CONTROL REGISTER (FCTR) - Read/Write
This register controls the UART enhanced functions that are not available on ST16C554 or ST16C654.
FCTR[7:6]: TX and RX FIFO Trigger Table Select
These 2 bits select the transmit and receive FIFO trigger level table A, B, C or D. When table A, B, or C is selected the auto RTS flow control trigger level is set to "next FIFO trigger level" for compatibility to ST16C550 and ST16C650 series. RTS/DTR# triggers on the next level of the RX FIFO trigger level, in another word, one FIFO level above and one FIFO level below. See in Table 16 for complete selection with FCR bit [5:4] and FCTR bits [7:6], i.e. if Table C is used on the receiver with RX FIFO trigger level set to 56 bytes, RTS/DTR# output will de-assert at 60 and re-assert at 16.
FCTR[5]: Auto RS485 Enable
Auto RS485 half duplex control enable/disable.
* Logic 0 = Standard ST16C550 mode. Transmitter generates an interrupt when transmit holding register
(THR) becomes empty. Transmit Shift Register (TSR) may still be shifting data bit out.
* Logic 1 = Enable Auto RS485 half duplex direction control. RTS# output changes from HIGH to LOW when
finished sending the last stop bit of the last character out of the TSR register. It changes from LOW to HIGH when a data byte is loaded into the THR or transmit FIFO. The change to HIGH occurs prior sending the start-bit. It also changes the transmitter interrupt from transmit holding to transmit shift register (TSR) empty.
52
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
FCTR[4]: Infrared RX Input Logic Select
* Logic 0 = Select RX input as active HIGH encoded IrDA data, normal, (default). * Logic 1 = Select RX input as active LOW encoded IrDA data, inverted.
FCTR [3:0] - Auto RTS/DTR Flow Control Hysteresis Select
These bits select the auto RTS/DTR flow control hysteresis and only valid when TX and RX Trigger Table-D is selected (FCTR bit [7:6] are set to logic 1). The RTS/DTR hysteresis is referenced to the RX FIFO trigger level. After reset, these bits are set to logic 0 selecting the next FIFO trigger level for hardware flow control. Table 19 below shows the 16 selectable hysteresis levels.
TABLE 19: 16 SELECTABLE HYSTERESIS LEVELS WHEN TRIGGER TABLE-D IS SELECTED
FCTR BIT [3] 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 FCTR BIT [2] 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 FCTR BIT [1] 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 FCTR BIT [0] 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 RTS/DTR HYSTERESIS (CHARACTERS) 0 +/- 4 +/- 6 +/- 8 +/- 8 +/- 16 +/- 24 +/- 32 +/- 12 +/- 20 +/- 28 +/- 36 +/- 40 +/- 44 +/- 48 +/- 52
5.14
Enhanced Feature Register (EFR) - Read/Write
Enhanced features are enabled or disabled using this register. Bits [3:0] provide single or dual consecutive character software flow control selection (see Table 20). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before programming a new setting.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS or DSR Flow Control.
* Logic 0 = Automatic CTS/DSR flow control is disabled (default). * Logic 1 = Enable Automatic CTS/DSR flow control. Transmission stops when CTS/DSR# pin de-asserts
(HIGH). Transmission resumes when CTS/DSR# pin is asserted (LOW). The selection for CTS# or DSR# is through MCR bit [2].
53
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT EFR[6]: Auto RTS or DTR Flow Control Enable
xr
REV. 1.0.0
RTS#/DTR# output may be used for hardware flow control by setting EFR bit [6] to logic 1. When Auto RTS/ DTR is selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level and RTS/DTR# will de-assert (HIGH) at the next upper trigger or selected hysteresis level. RTS/DTR# will reassert (LOW) when FIFO data falls below the next lower trigger or selected hysteresis level (see FCTR bits 47). The RTS# or DTR# output must be asserted (LOW) before the auto RTS/DTR can take effect. The selection for RTS# or DTR# is through MCR bit [2]. RTS/DTR# pin will function as a general purpose output when hardware flow control is disabled.
* Logic 0 = Automatic RTS/DTR flow control is disabled (default). * Logic 1 = Enable Automatic RTS/DTR flow control.
EFR[5]: Special Character Detect Enable
* Logic 0 = Special Character Detect Disabled (default). * Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the received data will be transferred to FIFO and ISR bit [4] will be set to indicate detection of the special character. bit [0] corresponds with the LSB bit for the receive character. If flow control is set for comparing Xon1, Xoff1 (EFR [1:0]=10) then flow control and special character work normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]=01) then flow control works normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character interrupt.
EFR[4]: Enhanced Function Bits Enable
Enhanced function control bit. This bit enables the enhanced functions in IER bits [7:5], ISR bits [5:4], FCR bits [5:4], MCR bits [7:5,3:2] and MSR [7:2] bits to be modified. After modifying any enhanced bits, EFR bit [4] can be set to a logic 0 to latch the new values. This feature prevents legacy software from altering or overwriting the enhanced functions once set. Normally, it is recommended to leave it enabled.
* Logic 0 = Disable write access to the enhanced function bits: IER bits [7:5], ISR bits [5:4], FCR bits [5:4],
MCR bits [7:5, 3:2] and MSR [7:2] bits. After a reset, all these bits are set to a logic 0 to be compatible with ST16C550 mode (default).
* Logic 1 = Enables write access to the enhanced function bits: IER bits [7:5], ISR bits [5:4], FCR bits [5:4],
MCR bits [7:5, 3:2] and MSR [7:2] bits.
EFR[3:0]: Software Flow Control Select
Combinations of software flow control can be selected by programming these bits, as shown in Table 20 below.
54
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 20: SOFTWARE FLOW CONTROL FUNCTIONS
EFR BIT [3] 0 0 1 0 1 X X X 1 0 1 0
EFR BIT [2] 0 0 0 1 1 X X X 0 1 1 0
EFR BIT [1] 0 X X X X 0 1 0 1 1 1 1
EFR BIT [0] 0 X X X X 0 0 1 1 1 1 1
TRANSMIT AND RECEIVE SOFTWARE FLOW CONTROL No TX and RX flow control (default and reset) No transmit flow control Transmit Xon1, Xoff1 Transmit Xon2, Xoff2 Transmit Xon1 and Xon2, Xoff1 and Xoff2 No receive flow control Receiver compares Xon1, Xoff1 Receiver compares Xon2, Xoff2 Transmit Xon1, Xoff1 Receiver compares Xon1 or Xon2, Xoff1 or Xoff2 Transmit Xon2, Xoff2 Receiver compares Xon1 or Xon2, Xoff1 or Xoff2 Transmit Xon1 and Xon2, Xoff1 and Xoff2 Receiver compares Xon1 and Xon2, Xoff1 and Xoff2 No transmit flow control Receiver compares Xon1 and Xon2, Xoff1 and Xoff2
5.15
TXCNT[7:0]: Transmit FIFO Level Counter - Read Only
Transmit FIFO level byte count from 0x00 (LOW) to 0x40 (64). This 8-bit register gives an indication of the number of characters in the transmit FIFO. The FIFO level Byte count register is read only. The user can take advantage of the FIFO level byte counter for faster data loading to the transmit FIFO, which reduces CPU bandwidth requirements.
5.16 TXTRG [7:0]: Transmit FIFO Trigger Level - Write Only
An 8-bit value written to this register sets the TX FIFO trigger level from 0x00 (zero) to 0x40 (64). The TX FIFO trigger level generates an interrupt whenever the data level in the transmit FIFO falls below this preset trigger level.
5.17 RXCNT[7:0]: Receive FIFO Level Counter - Read Only
Receive FIFO level byte count from 0x00 (zero) to 0x40 (64). It gives an indication of the number of characters in the receive FIFO. The FIFO level byte count register is read only. The user can take advantage of the FIFO level byte counter for faster data unloading from the receiver FIFO, which reduces CPU bandwidth requirements.
5.18 RXTRG[7:0]: Receive FIFO Trigger Level - Write Only
An 8-bit value written to this register, sets the RX FIFO trigger level from 0x00 (zero) to 0x40 (64). The RX FIFO trigger level generates an interrupt whenever the receive FIFO level rises to this preset trigger level.
5.19 XOFF1, XOFF2, XON1 AND XON2 REGISTERS, WRITE ONLY
These registers are used to program the Xoff1, Xoff2, Xon1 and Xon2 control characters respectively.
55
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT 5.20 XCHAR REGISTER, READ ONLY
xr
REV. 1.0.0
This register gives the status of the last sent control character (Xon or Xoff) and the last received control character (Xon or Xoff). This register will be reset to 0x00 if, at anytime, the Software Flow Control is disabled.
XCHAR [7:4]: Reserved XCHAR [3]: Transmit Xon Indicator
If the last transmitted control character was a Xon character or characters (Xon1, Xon2), this bit will be set to a logic 1. This bit will clear after the read.
XCHAR [2]: Transmit Xoff Indicator
If the last transmitted control character was a Xoff character or characters (Xoff1, Xoff2), this bit will be set to a logic 1. This bit will clear after the read.
XCHAR [1]: Xon Detect Indicator
If the last received control character was a Xon character or characters (Xon1, Xon2), this bit will be set to a logic 1. This bit will clear after the read.
XCHAR [0]: Xoff Detect Indicator
If the last received control character was a Xoff character or characters (Xoff1, Xoff2), this bit will be set to a logic 1. This bit will clear after the read.
56
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT TABLE 21: UART RESET CONDITIONS
REGISTERS DLL DLM DLD RHR THR IER FCR ISR LCR MCR LSR MSR SPR FCTR EFR TFCNT TFTRG RFCNT RFTRG XCHAR XON1 XON2 XOFF1 XOFF2
RESET STATE Bits [7:0] = 0x01 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0xXX Bits [7:0] = 0xXX Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x01 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x60 Bits [3:0] = logic 0 Bits [7:4] = logic levels of the inputs Bits [7:0] = 0xFF Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00 Bits [7:0] = 0x00
I/O SIGNALS TX[7:0] IRTX[7:0] RTS#[7:0] DTR#[7:0] EECK EECS EEDI
RESET STATE HIGH LOW HIGH HIGH LOW LOW LOW
57
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
ABSOLUTE MAXIMUM RATINGS
Power Supply Range Voltage at Any Pin Operating Temperature Storage Temperature Package Dissipation Thermal Resistance (20x20x1.4mm 144-LQFP) 4 Volts -0.5 to 4V -40o to +85o C -65o to +150o C 500 mW theta-ja = 42, theta-jc = 8
ELECTRICAL CHARACTERISTICS
DC ELECTRICAL CHARACTERISTICS FOR 3.3V SIGNALLING TA=-40O TO +85OC (INDUSTRIAL GRADE) SUPPLY VOLTAGE, VCC = 3.0 - 3.6V
SYMBOL PARAMETER MIN -0.5 VIL Input Low Voltage -0.5 0.5VCC VIH Input High Voltage 2.0 2.0 MAX 0.3VCC 0.8 VCC + 0.5 6.0 VCC + 0.5 0.1VCC VOL Output Low Voltage 0.9VCC VOH IIL ICL CIN CCLK CIDSEL IOff ICC Output High Voltage Input Leakage Current Input Clock Leakage Input Pin Capacitance CLK Pin Capacitance IDSEL Pin Capacitance PME# input leakage Power Supply Current 5 2.4 10 10 10 12 8 1 4 0.4 V V V V A A pF pF pF A mA Vo 3.6V, VCC off or floating PCI bus CLK and Ext. Clock = 2MHz, all inputs at VCC or GND and all outputs are unloaded. All eight UARTs asleep. AD[31:0] at GND, all inputs at VCC or GND. UNIT
S
CONDITION For PCI bus inputs For Non-PCI bus inputs For PCI bus inputs For Non-PCI bus inputs For external clock (XTAL1) input only IOL = 1.5mA IOL = 6mA IOH = -0.5mA IOH = -2mA 0 < Vin < VCC
NOTES
V V V V
5V tolerant inputs Not 5V tolerant PCI bus outputs Non-PCI bus outputs PCI bus outputs Non-PCI bus outputs
ISLEEP
Sleep Current
1
mA
58
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
AC ELECTRICAL CHARACTERISTICS FOR 3.3V SIGNALING TA=-40O TO+85OC (INDUSTRIAL GRADE) VCC = 3.0 - 3.6V
SYMBOL XTAL1 ECLK IOH(AC, min) PARAMETER UART Crystal Oscillator External Clock Switching Current High, Min -12VCC -32VCC 16VCC 38VCC 25+(Vin-VCC-1)/0.015 -25+(Vin+1)/0.015 1 1 15 6 6 1.5 2 2 14 3 5 0 1 100 40 225 5 50 4 6 4 4 MIN MAX 24 64 UNITS MHz MHz mA mA mA mA mA mA V/ns V/ns ns ns ns V/ns ns ns ns ns ns ns ms us ns clocks clocks mV/ns Bused and point to point signals NOTES On-chip osc. Max 8Mbps using 8X Vout = 0.3VCC Vout = 0.7VCC Vout = 0.6VCC Vout = 0.18VCC VCC+4 > Vin VCC+1 -3 < Vin -1 0.3VCC to 0.6VCC 0.6VCC to 0.3VCC PCI bus Clock, CLK up to 66.67MHz
IOH(AC, max) Switching Current High, Max IOL(AC, min) IOL(AC, max) ICH ICL SlewR SlewF Tcyc Thigh Tlow Switching Current Low, Min Switching Current Low, Max High Clamp Current Low Clamp Current Output Rise Slew Rate Output Fall Slew Rate CLK Cycle Time CLK High Time CLK Low Time CLK Slew Rate Tval Ton Toff Tsu Tsu (ptp) Th Trst Trst-clk# Trst-off Trhfa Trhff CLK to Signal Valid Delay Float to Active Delay Active to Float Delay Input Setup Time to CLK bused signals Input Setup Time to CLK point to point signals Input Hold Time from CLK RST# Active Time After Power Stable RST# Active Time After CLK Stable Reset Active to output float delay RST# HIGH to first Configuration access RST# HIGH to first FRAME# assertion RST# Slew Rate
59
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT FIGURE 19. PCI BUS CONFIGURATION SPACE REGISTERS READ AND WRITE OPERATION
xr
REV. 1.0.0
Host
CLK
1 2 3 4
FRAME#
Host
AD[31:0]
Host Target
ADDRESS
DATA
C/BE[3:0]#
Host
CFG-RD
BYTE ENABLE#
IRDY#
Host
TRDY#
Target
DEVSEL#
Target PCICFG_RD
Host
CLK
1 2 3 4
FRAME#
Host
AD[31:0]
Host Target
ADDRESS
WRITE DATA
C/BE[3:0]#
Host
CFG-WR
BYTE ENABLE#
IRDY#
Host
TRDY#
Target
DEVSEL#
Target PCICFG_WR
60
DATA TRANSFER
DATA TRANSFER
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
FIGURE 20. DEVICE CONFIGURATION AND UART REGISTERS READ OPERATION FOR A BYTE OR DWORD
CLK
Host
1
2
3
4
5
6
7
8
9
10
11
FRAME#
Host
AD[31:0]
Host Target
Address
Data BYTE
Data WORD
C/BE[3:0]#
Host
Bus CMD
Byte Enable# = BYTE BYTE TRANSFER
Byte Enable# = DWORD DWORD TRANSFER Data Parity
IRDY#
Host
WAIT
WAIT
WAIT
WAIT
TRDY#
Target
DEVSEL#
Target
PAR
Host Target
Address Parity
Data Parity
PERR#
Target
Active
WAIT
Active
SERR# Targe
t
Active
Note: PERR# and SERR are optional in a bus target application. Even Parity is on AD[31:0], C/BE[3:0]#, and PAR
PCI_RD1
61
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
FIGURE 21. DEVICE CONFIGURATION REGISTERS, UART REGISTERS AND TRANSMIT DATA BURST WRITE OPERATION
CLK
Host
1
2
3
4
5
6
7
8
9
10
11
FRAME#
Host
AD[31:0]
Host Target
Address
Data DWORD
Data DWORD
Data DWORD
Data DWORD
Data DWORD
C/BE[3:0]#
Host
Bus CMD DWORD TRANSFER
Byte Enable# = DWORD
DWORD TRANSFER
DWORD TRANSFER
DWORD TRANSFER
IRDY#
Host
TRDY#
Target
DEVSEL#
Target
PAR
Host Target
Address Parity
Data Parity
Data Parity
Data Parity
Data Parity
DWORD TRANSFER Data Parity Active Active
PERR#
Target
Active
Active
Active
SERR#
Target
Active
Note: PERR# and SERR are optional in a bus target application. Even Parity is on AD[31:0], C/BE[3:0]#, and PAR
PCI BWR
62
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
FIGURE 22. DEVICE CONFIGURATION REGISTERS, UART REGISTERS AND RECEIVE DATA BURST READ OPERATION
CLK
Host
1
8
13
18
23
FRAME#
Host
AD[31:0]
Host Target
AD
Data
Data
Data
Data
C/BE[3:0]#
Host
Bus CMD
Byte Enable# = DWORD
DWORD TRANSFER
DWORD TRANSFER
DWORD TRANSFER
IRDY#
Host
TRDY#
Target
DEVSEL#
Target
PAR
Host Target
AD
DWORD TRANSFER
Data Data Active Active
Data
Data
PERR#
Target
Active
Active
SERR#
Target
Active
Note: PERR# and SERR are optional in a bus target application. Even Parity is on AD[31:0], C/BE[3:0]#, and PAR
PCI_BRD
63
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT FIGURE 23. 3.3V PCI BUS CLOCK (DC TO 66MHZ)
T_cyc
xr
REV. 1.0.0
T_high
T_low
0.6VCC
0.5VCC
CLK
0.4VCC 0.3VCC
0.4 VCC, p-to-p (minimum) 0.2VCC
T_val
V_trise V_tfall
Output Delay
Measurement Condition Parameters Vth = 0.6VCC Vtl = 0.2VCC Vtest = 0.4VCC Vtrise = 0.285VCC Vtfall = 0.615VCC Vmax = 0.4VCC Input Signal Slew Rate = 1.5 V/ns
T_on
Tri-State Output
T_off T_su V_th Input V_tl V_test Inputs Valid V_max T_h
pci_clk
64
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
FIGURE 24. TRANSMIT DATA INTERRUPT AT TRIGGER LEVEL
START BIT STOP BIT
DATA BITS (5-8) D0 D1 D2 D3 D4 D5 D6 D7
TX Data
5 DATA BITS 6 DATA BITS 7 DATA BITS
PARITY BIT
NEXT DATA START BIT
TX Interrupt at Transmit Trigger Level
Set at Below Trigger Level
Clear at Above Trigger Level
BAUD RATE CLOCK of 16X or 8X
TXNOFIFO-1
FIGURE 25. RECEIVE DATA READY INTERRUPT AT TRIGGER LEVEL
START BIT STOP BIT
DATA BITS (5-8) D0 D1 D2 D3 D4 D5 D6 D7
RX Data Input
PARITY BIT
First byte that reaches the trigger level
RX Data Ready Interrupt at Receive Trigger Level
De-asserted at below trigger level
Asserted at above trigger level
RXFIFO1
65
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
PACKAGE DIMENSIONS
144 LEAD LOW-PROFILE QUAD FLAT PACK (20 x 20 x 1.4 mm LQFP)
D D1 108 73
109
72
D1
D
144
37
1 A2 e A Seating Plane A1 B
36
C
L
NOTE: Note: The control dimension is the millimeter column INCHES SYMBOL A A1 A2 B C D D1 e L MIN 0.055 0.002 0.053 0.007 0.004 0.858 0.783 0.020 BSC 0.018 0x 0.030 7x MAX 0.063 0.006 0.057 0.011 0.008 0.874 0.791 MILLIMETERS MIN 1.40 0.05 1.35 0.17 0.09 21.80 19.90 0.50 BSC 0.45 0x 0.75 7x MAX 1.60 0.15 1.45 0.27 0.20 22.20 20.10
66
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
REVISION HISTORY
DATE March 2005 August 2005 REVISION P1.0.0 P1.0.1 Preliminary Datasheet Updated Timer/Counter Description to include 'Reset Timer' command. Updated the 1.4mm-thick Quad Flat Pack package description from "TQFP" to "LQFP" to be consistent with JEDEC and Industry norms. Final Datasheet release. DESCRIPTION
November 2005
1.0.0
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user's specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2005 EXAR Corporation Datasheet November 2005. Send your UART technical inquiry with technical details to hotline: uarttechsupport@exar.com. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
67
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
TABLE OF CONTENTS
GENERAL DESCRIPTION ................................................................................................ 1
APPLICATIONS............................................................................................................................................... 1 FEATURES .................................................................................................................................................... 1
FIGURE 1. BLOCK DIAGRAM OF THE XR17V258 ............................................................................................................................... 1 FIGURE 2. PIN OUT OF THE DEVICE.................................................................................................................................................. 2 ORDERING INFORMATION................................................................................................................................ 2
PIN DESCRIPTIONS ......................................................................................................... 3 FUNCTIONAL DESCRIPTION .......................................................................................... 8
PCI Local Bus Interface .............................................................................................................................................. PCI Local Bus Configuration Space Registers ........................................................................................................... Power Management Registers ................................................................................................................................... EEPROM Interface ..................................................................................................................................................... 8 8 8 8
1.0 XR17V258 INTERNAL REGISTERS........................................................................................................ 9
FIGURE 3. THE XR17V258 REGISTER SETS..................................................................................................................................... 9
1.1 PCI LOCAL BUS CONFIGURATION SPACE REGISTERS ............................................................................... 9
TABLE 1: PCI LOCAL BUS CONFIGURATION SPACE REGISTERS ....................................................................................................... 10
1.2 POWER MANAGEMENT REGISTERS ............................................................................................................. 11
TABLE 2: POWER MANAGEMENT REGISTERS ................................................................................................................................... 11 1.2.1 POWER STATES AND POWER STATE TRANSITIONS OF THE V258 ..................................................................... 12
D0 State.................................................................................................................................................................... 12 D3hot State............................................................................................................................................................... 12 D3cold State ............................................................................................................................................................. 13
FIGURE 4. POWER STATE TRANSITIONS OF THE XR17V258............................................................................................................ 13
1.3 SPECIAL READ/WRITE REGISTER TO STORE USER INFORMATION ........................................................ 13
TABLE 3: SPECIAL READ/WRITE REGISTER ..................................................................................................................................... 13
1.4 EEPROM INTERFACE....................................................................................................................................... 14
TABLE 4: EEPROM ADDRESS DEFINITIONS .................................................................................................................................... 14
1.5 DEVICE INTERNAL REGISTER SETS ............................................................................................................. 14
TABLE 5: XR17V258 UART AND DEVICE CONFIGURATION REGISTERS ........................................................................................... 15
1.6 DEVICE CONFIGURATION REGISTERS ......................................................................................................... 17
TABLE 6: DEVICE CONFIGURATION REGISTERS SHOWN IN BYTE ALIGNMENT ................................................................................... 17 TABLE 7: DEVICE CONFIGURATION REGISTERS SHOWN IN DWORD ALIGNMENT ............................................................................... 18 1.6.1 THE GLOBAL INTERRUPT REGISTER....................................................................................................................... 18 FIGURE 5. THE GLOBAL INTERRUPT REGISTER, INT0, INT1, INT2 AND INT3 .................................................................................. 19 TABLE 8: UART CHANNEL [7:0] INTERRUPT SOURCE ENCODING ..................................................................................................... 19 TABLE 9: UART CHANNEL [7:0] INTERRUPT CLEARING ................................................................................................................... 19 1.6.2 GENERAL PURPOSE 16-BIT TIMER/COUNTER [TIMERMSB, TIMELSB, TIMER, TIMECNTL] (DEFAULT 0XXX-XX-0000)................................................................................................................................................................................... 20 FIGURE 6. TIMER/COUNTER CIRCUIT............................................................................................................................................... 20 TABLE 10: TIMER CONTROL REGISTERS .................................................................................................................................... 21
TIMER OPERATION ................................................................................................................................................ 21
FIGURE 7. TIMER OUTPUT IN ONE-SHOT AND RE-TRIGGERABLE MODES .......................................................................................... FIGURE 8. INTERRUPT OUTPUT (ACTIVE LOW) IN ONE-SHOT AND RE-TRIGGERABLE MODES............................................................ 1.6.3 8XMODE [7:0] (DEFAULT 0X00).................................................................................................................................. 1.6.4 REGA [15:8] (DEFAULT 0X00) RESERVED................................................................................................................ 1.6.5 RESET [23:16] (DEFAULT 0X00)................................................................................................................................. 1.6.6 SLEEP [31:24] (DEFAULT 0X00) ................................................................................................................................. 1.6.7 DEVICE IDENTIFICATION AND REVISION ................................................................................................................. 1.6.8 REGB REGISTER ......................................................................................................................................................... 1.6.9 MULTI-PURPOSE INPUTS AND OUTPUTS ................................................................................................................ 1.6.10 MPIO REGISTERS ...................................................................................................................................................... FIGURE 9. MULTIPURPOSE INPUT/OUTPUT INTERNAL CIRCUIT ........................................................................................................... 22 23 23 23 23 24 24 25 25 25 26
2.0 CRYSTAL OSCILLATOR / BUFFER ..................................................................................................... 27
FIGURE 10. TYPICAL OSCILLATOR CONNECTIONS............................................................................................................................. 28
3.0 TRANSMIT AND RECEIVE DATA ......................................................................................................... 28
3.1 FIFO DATA LOADING AND UNLOADING IN 32-BIT FORMAT. ..................................................................... 28
3.1.1 NORMAL RX FIFO DATA UNLOADING AT LOCATIONS 0X100, 0X300, 0X500, 0X700.......................................... 28 3.1.2 SPECIAL RX FIFO DATA UNLOADING AT LOCATIONS 0X180, 0X380, 0X580, AND 0X780 ................................. 29 3.1.3 TX FIFO DATA LOADING AT LOCATIONS 0X100, 0X300, 0X500, 0X700, 0X900, 0XB00, 0XD00, 0XF00 ............. 30
3.2 FIFO DATA LOADING AND UNLOADING THROUGH THE UART CHANNEL REGISTERS, THR AND RHR IN 8-
I
xr
REV. 1.0.0
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
BIT FORMAT................................................................................................................................................... 30
TABLE 11: TRANSMIT AND RECEIVE DATA REGISTER IN BYTE FORMAT, 16C550 COMPATIBLE .......................................................... 31
4.0 UART...................................................................................................................................................... 31
4.1 PROGRAMMABLE BAUD RATE GENERATOR WITH FRACTIONAL DIVISOR ........................................... 31
FIGURE 11. BAUD RATE GENERATOR ............................................................................................................................................. 32 TABLE 12: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING ................................................. 32
4.2 AUTOMATIC HARDWARE (RTS/CTS OR DTR/DSR) FLOW CONTROL OPERATION................................. 33
FIGURE 12. AUTO RTS/DTR AND CTS/DSR FLOW CONTROL OPERATION...................................................................................... 34
4.3 INFRARED MODE ............................................................................................................................................. 34
FIGURE 13. INFRARED TRANSMIT DATA ENCODING AND RECEIVE DATA DECODING.......................................................................... 35
4.4 INTERNAL LOOPBACK.................................................................................................................................... 35
FIGURE 14. INTERNAL LOOP BACK ................................................................................................................................................. 36
4.5 UART CHANNEL CONFIGURATION REGISTERS AND ADDRESS DECODING .......................................... 36
TABLE 13: UART CHANNEL CONFIGURATION REGISTERS. .................................................................................................. 37 TABLE 14: UART CHANNEL CONFIGURATION REGISTERS DESCRIPTION. SHADED BITS ARE ENABLED BY EFR BIT-4. ....... 38
4.6 TRANSMITTER.................................................................................................................................................. 39
4.6.1 TRANSMIT HOLDING REGISTER (THR)..................................................................................................................... 4.6.2 TRANSMITTER OPERATION IN NON-FIFO MODE .................................................................................................... FIGURE 15. TRANSMITTER OPERATION IN NON-FIFO MODE ............................................................................................................ 4.6.3 TRANSMITTER OPERATION IN FIFO MODE ............................................................................................................. 4.6.4 AUTO RS485 OPERATION .......................................................................................................................................... FIGURE 16. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE ................................................................................... 4.7.1 RECEIVER OPERATION IN NON-FIFO MODE .......................................................................................................... FIGURE 17. RECEIVER OPERATION IN NON-FIFO MODE.................................................................................................................. 4.7.2 RECEIVER OPERATION WITH FIFO........................................................................................................................... FIGURE 18. RECEIVER OPERATION IN FIFO AND FLOW CONTROL MODE ......................................................................................... 39 39 40 40 40 40 41 41 41 41
4.7 RECEIVER ......................................................................................................................................................... 41
5.0 UART CONFIGURATION REGISTERS ................................................................................................ 42
5.1 RECEIVE HOLDING REGISTER (RHR) - READ ONLY ................................................................................... 5.2 TRANSMIT HOLDING REGISTER (THR) - WRITE ONLY ............................................................................... 5.3 BAUD RATE GENERATOR DIVISORS (DLM, DLL AND DLD)....................................................................... 5.4 INTERRUPT ENABLE REGISTER (IER) - READ/WRITE ................................................................................ 42 42 42 42
5.4.1 IER VERSUS RECEIVE FIFO INTERRUPT MODE OPERATION ............................................................................... 42 5.4.2 IER VERSUS RECEIVE/TRANSMIT FIFO POLLED MODE OPERATION.................................................................. 42
5.5 INTERRUPT STATUS REGISTER (ISR) - READ ONLY .................................................................................. 43
5.5.1 INTERRUPT GENERATION: ........................................................................................................................................ 44 5.5.2 INTERRUPT CLEARING: ............................................................................................................................................. 44 TABLE 15: INTERRUPT SOURCE AND PRIORITY LEVEL ..................................................................................................................... 44
5.6 FIFO CONTROL REGISTER (FCR) - WRITE ONLY......................................................................................... 45
TABLE 16: TRANSMIT AND RECEIVE FIFO TRIGGER TABLE AND LEVEL SELECTION .......................................................................... 46
5.7 LINE CONTROL REGISTER (LCR) - READ/WRITE ........................................................................................ 46
TABLE 17: PARITY PROGRAMMING ................................................................................................................................................. 47
5.8 MODEM CONTROL REGISTER (MCR) - READ/WRITE .................................................................................. 5.9 LINE STATUS REGISTER (LSR) - READ ONLY.............................................................................................. 5.10 MODEM STATUS REGISTER (MSR) - READ ONLY ..................................................................................... 5.11 MODEM STATUS REGISTER (MSR) - WRITE ONLY....................................................................................
48 49 50 51
TABLE 18: AUTO RS485 HALF-DUPLEX DIRECTION CONTROL DELAY FROM TRANSMIT-TO-RECEIVE ................................................. 51
5.12 SCRATCH PAD REGISTER (SPR) - READ/WRITE ....................................................................................... 52 5.13 FEATURE CONTROL REGISTER (FCTR) - READ/WRITE ........................................................................... 52
TABLE 19: 16 SELECTABLE HYSTERESIS LEVELS WHEN TRIGGER TABLE-D IS SELECTED ................................................................ 53
5.14 ENHANCED FEATURE REGISTER (EFR) - READ/WRITE ........................................................................... 53
TABLE 20: SOFTWARE FLOW CONTROL FUNCTIONS ........................................................................................................................ 55
5.15 TXCNT[7:0]: TRANSMIT FIFO LEVEL COUNTER - READ ONLY ................................................................ 5.16 TXTRG [7:0]: TRANSMIT FIFO TRIGGER LEVEL - WRITE ONLY ............................................................... 5.17 RXCNT[7:0]: RECEIVE FIFO LEVEL COUNTER - READ ONLY................................................................... 5.18 RXTRG[7:0]: RECEIVE FIFO TRIGGER LEVEL - WRITE ONLY .................................................................. 5.19 XOFF1, XOFF2, XON1 AND XON2 REGISTERS, WRITE ONLY................................................................... 5.20 XCHAR REGISTER, READ ONLY ..................................................................................................................
55 55 55 55 55 56
TABLE 21: UART RESET CONDITIONS ...................................................................................................................................... 57
ABSOLUTE MAXIMUM RATINGS ................................................................................. 58 ELECTRICAL CHARACTERISTICS............................................................................... 58
DC ELECTRICAL CHARACTERISTICS FOR 3.3V SIGNALLING................................................................. 58
II
XR17V258 66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
xr
REV. 1.0.0
TA=-40o to +85oC (industrial grade) Supply Voltage, VCC = 3.0 - 3.6V.................................................................. 58
AC ELECTRICAL CHARACTERISTICS FOR 3.3V SIGNALING ............................................................... 59
TA=-40o to+85oC (industrial grade) VCC = 3.0 - 3.6V............................................................................................. 59
FIGURE 19. PCI BUS CONFIGURATION SPACE REGISTERS READ AND WRITE OPERATION................................................................. FIGURE 20. DEVICE CONFIGURATION AND UART REGISTERS READ OPERATION FOR A BYTE OR DWORD ...................................... FIGURE 21. DEVICE CONFIGURATION REGISTERS, UART REGISTERS AND TRANSMIT DATA BURST WRITE OPERATION ..................... FIGURE 22. DEVICE CONFIGURATION REGISTERS, UART REGISTERS AND RECEIVE DATA BURST READ OPERATION ........................ FIGURE 23. 3.3V PCI BUS CLOCK (DC TO 66MHZ) ....................................................................................................................... FIGURE 24. TRANSMIT DATA INTERRUPT AT TRIGGER LEVEL ........................................................................................................... FIGURE 25. RECEIVE DATA READY INTERRUPT AT TRIGGER LEVEL.................................................................................................. 60 61 62 63 64 65 65
PACKAGE DIMENSIONS................................................................................................ 66
TABLE OF CONTENTS......................................................................................................
REVISION HISTORY...................................................................................................................................... 67 I
III

▲Up To Search▲

Price & Availability of XR17V258

	To Download XR17V258 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .